manualshive.com logo in svg

NXP Semiconductors MC56F80000-EVKUM, Руководство пользователя, Страница: 14 / 26

Поделиться
Скачать
NXP Semiconductors MC56F80000-EVKUM Скачать руководство пользователя страница 14

NXP Semiconductors

MC56F80000-EVKUM

MC56F80000-EVK Board User Manual

2.3 3-axis digital sensor

The MC56F80000-EVK board supports motion sensing using NXP FXLS8974CFR3

accelerometer. FXLS8974CFR3 is a compact 3-axis MEMS accelerometer designed for

use in applications that require ultra-low-power wake-up on motion.
FXLS8974CFR3 is connected to MC56F80748 through I2C interface, LPI2C. The

INTF_SEL pin of FXLS8974CFR3 has been connected to GND, so that I2C interface

mode is selected for this device.
The SA0 pin of the FXLS8974CFR3 device selects the least significant bit of its I2C

secondary address (device address). SA0 is set to 0 by default, remove R101 to set SA0

to 1.

•

When SA0 = 0, the I2C address (7-bit format) of the FXLS8974CFR3 device is set to

18h (default)

•

When SA0 = 1, the I2C address (7-bit format) of the FXLS8974CFR3 device is set to

19h

Since the BT_MODE pin of the device is connected to GND, default operation mode is

enabled. For more information, refer to FXLS8974CF data sheet.
The following figure shows the accelerometer circuit diagram.

VDD

VDD

VDD

VDD

C66

0.1 µF

R101

0

R160

0

R100

0

DNP

R152

0

C65

4.7 µF

R92

0

FXLS 8974CFR3

U18

BT_MODE

2

SCL/SCLK

5

INTF_SEL

9

SPI_CS/WAKE_UP

7

SA0/SPI_MISO

3

SDA/SPI_MOSI/SPI_DATA

4

INT1/MOT_DET

8

INT2/EXT_TRIG/BOOT_OUT

6

V

D

D

1

G

N

D

1

0

R98

10K

C67

0.1 µF

R159

0

DNP

R93

0

R87
10K
DNP

R85

4.7K

R86
10K
DNP

R89

0

R84
4.7K

GF3

GF8

GF2

GF6
GC13

INT1_COMBO

INT2_COMBO

WAKE_UP

LP_SCL0

LP_SDA0

Figure 8. Accelerometer circuit diagram

FXLS8974CFR3 pin/signal

MC56F80748 pin

Description

SCL/SCLK

GPIOF3 (LP_SCL0)

I2C serial clock

SDA

GPIOF2 (LP_SDA0)

I2C serial data

INT1/MOT_DET

GPIOF6 (INT1_COMBO)

Mode-dependent multifunction I/O pin 1. For more detail,

refer to 

FXLS8974CF data sheet

.

INT2/EXT_TRIG/BOOT_OUT GPIOC13 (INT2_COMBO)

(disconnected from GPIOC13

by default)

Mode-dependent multifunction I/O pin 2. For more detail,

refer to 

FXLS8974CF data sheet

.

Table 12. FXLS8974CFR3 pin connections

MC56F80000-EVKUM

All information provided in this document is subject to legal disclaimers.

© 2022 NXP B.V. All rights reserved.

User manual

Rev. 1 — 14 December 2022

14 / 26

Содержание MC56F80000-EVKUM



























Отзывы:

Нет отзывов