NXP Semiconductors LPC822M101JDH20 Скачать руководство пользователя страница 124 | Manualshive

Страница: 124 / 487

NXP Semiconductors LPC822M101JDH20 Скачать руководство пользователя страница 124

UM10800

All information provided in this document is subject to legal disclaimers.

© NXP Semiconductors N.V. 2016. All rights reserved.

User manual

Rev. 1.2 — 5 October 2016

124 of 487

9.1 How to read this chapter

All GPIO registers refer to 32 pins on each port. Depending on the package type, not all
pins are available, and the corresponding bits in the GPIO registers are reserved.

9.2 Basic configuration

For the GPIO port registers, enable the clock to the GPIO port in the SYSAHBCLKCTRL
register (

9.3 Features

•

GPIO pins can be configured as input or output by software.

•

All GPIO pins default to inputs with interrupt disabled at reset.

•

Pin registers allow pins to be sensed and set individually.

•

Direction (input/output) can be set and cleared individually.

9.4 General description

The GPIO pins can be used in several ways to set pins as inputs or outputs and use the
inputs as combinations of level and edge sensitive interrupts.

The GPIOs can be used as external interrupts together with the pin interrupt block.

The GPIO port registers configure each GPIO pin as input or output and read the state of
each pin if the pin is configured as input or set the state of each pin if the pin is configured
as output.

9.5 Register description

Note: In all GPIO registers, bits that are not shown are reserved.

GPIO port addresses can be read and written as bytes, halfwords, or words.

Remark:

ext in this table and subsequent tables indicates that the data read after reset

depends on the state of the pin, which in turn may depend on an external source.

UM10800

Chapter 9: LPC82x General Purpose I/O (GPIO)

Rev. 1.2 — 5 October 2016

User manual

Table 112. GPIO pins available

Package

GPIO Port 0

TSSOP20

PIO0_0 to PIO0_5; PIO0_8 to PIO0_15; PIO0_17; PIO0_23

HVQFN33

PIO0_0 to PIO0_28

«
...
122
123
124
125
126
...
»

Содержание LPC822M101JDH20








































































































































































































































































































































































































































































































Отзывы:

Нет отзывов