NXP Semiconductors LPC5410x Скачать руководство пользователя страница 433 | Manualshive

Страница: 433 / 463

NXP Semiconductors LPC5410x Скачать руководство пользователя страница 433

UM10850

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 2.4 — 13 September 2016

434 of 464

NXP Semiconductors

UM10850

Chapter 31: LPC5410x Flash API

Up to 4 parameters can be passed in the r0, r1, r2 and r3 registers respectively (see the

ARM Thumb Procedure Call Standard SWS ESPC 0002 A-05)

. Additional parameters are

passed on the stack. Up to 4 parameters can be returned in the r0, r1, r2 and r3 registers
respectively. Additional parameters are returned indirectly via memory. Some of the IAP
calls require more than 4 parameters. If the ARM suggested scheme is used for the
parameter passing/returning then it might create problems due to difference in the C
compiler implementation from different vendors. The suggested parameter passing
scheme reduces such risk.

The flash memory is not accessible during a write or erase operation. IAP commands,
which results in a flash write/erase operation, use 32 bytes of space in the top portion of
the on-chip RAM for execution. The user program should not be use this space if IAP flash
programming is permitted in the application.

Table 496. IAP Command Summary

IAP Command

Command code

Reference

Prepare sector(s) for write operation

50 (decimal)

Copy RAM to flash

51 (decimal)

Erase sector(s)

52 (decimal)

Blank check sector(s)

53 (decimal)

Read Part ID

54 (decimal)

Read Boot code version

55 (decimal)

Compare

56 (decimal)

Reinvoke ISP

57 (decimal)

Read UID

58 (decimal)

Erase page(s)

59 (decimal)

Read Signature

70 (decimal)

Fig 62. IAP parameter passing

&RPPDQGFRGH

3DUDP

3DUDP

3DUDPQ

VWDWXVBUHVXOW>@

VWDWXVBUHVXOW>@

6WDWXVFRGH

5HVXOW

5HVXOW

5HVXOWQ

&RPPDQG3DUDPHWHU$UUD\

6WDWXV5HVXOW$UUD\

$505(*,67(5U

$505(*,67(5U

FRPPDQGBSDUDP>@

FRPPDQGBSDUDP>@

FRPPDQGBSDUDP>@

FRPPDQGBSDUDP>Q@

VWDWXVBUHVXOW>@

VWDWXVBUHVXOW>Q@

«
...
431
432
433
434
435
...
»

Содержание LPC5410x
















































































































































































































































































































































































































































































Отзывы:

Нет отзывов