manualshive.com logo in svg

NXP Semiconductors LPC5410x, Руководство пользователя

Микроконтроллеры NXP Semiconductors LPC5410x - мощные устройства для встроенных систем. Инструкция пользователя доступна для свободного скачивания на manualshive.com. Получите полный контроль над вашим устройством, загрузив бесплатный руководство пользователя.

Поделиться
Скачать
background image

UM10850

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 2.4 — 13 September 2016 

193 of 464

NXP Semiconductors

UM10850

Chapter 13: LPC5410x SCTimer/PWM (SCT0)

13.6.26 SCT output set registers 0 to 7

Based on a selected event, each SCT output can be set.

There is one output set register for each SCT output which selects which events can set 
that output. Each bit of an output set register is associated with a different event (bit 0 with 
event 0, etc.). A selected event can set or clear the output depending on the setting of the 
SETCLRn field in the OUTPUTDIRCTRL register. To define the actual event that sets the 
output (a match, an I/O pin toggle, etc.), see the EVn_CTRL register.

Remark: 

If the SCTimer/PWM is operating as two 16-bit counters, events can only modify 

the state of the outputs when neither counter is halted. This is true regardless of what 
triggered the event.

 

13.6.27 SCT output clear registers 0 to 7

Based on a selected event, each SCT output can be cleared.

There is one register for each SCT output which selects which events can clear that 
output. Each bit of an output clear register is associated with a different event (bit 0 with 
event 0, etc.). A selected event can clear or set the output depending on the setting of the 
SETCLRn field in the OUTPUTDIRCTRL register. To define the actual event that clears 
the output (a match, an I/O pin toggle, etc.), see the EVn_CTRL register. 

20

MATCHMEM

If this bit is one and the COMBMODE field specifies a match component to the 
triggering of this event, then a match is considered to be active whenever the 
counter value is GREATER THAN OR EQUAL TO the value specified in the match 
register when counting up, LESS THEN OR EQUAL TO the match value when 
counting down.

If this bit is zero, a match is only be active during the cycle when the counter is 
equal to the match value.

0

22:21

DIRECTION

Direction qualifier for event generation. This field only applies when the counters 
are operating in BIDIR mode. If BIDIR = 0, the SCT ignores this field. Value 0x3 is 
reserved.

0

0x0

Direction independent. This event is triggered regardless of the count direction.

0x1

Counting up. This event is triggered only during up-counting when BIDIR = 1.

0x2

Counting down. This event is triggered only during down-counting when BIDIR = 1.

31:23

-

Reserved

-

Table 234. SCT event control register 0 to 12 (EV[0:12]_CTRL, address 0x5000 4304 (EV0_CTRL) to 0x5000 4364 

(EV12_CTRL)) bit description

Bit

Symbol

Value

Description

Reset 
value

Table 235. SCT output set register (OUT[0:7]_SET, address 0x5000 4500 (OUT0_SET) to 0x5000 4538 (OUT7_SET) bit 

description

Bit

Symbol

Description

Reset 
value

15:0

SET

A 1 in bit m selects event m to set output n (or clear it if SETCLRn = 0x1 or 0x2) event 0 = bit 0, 
event 1 = bit 1, …up to the number of bits = number of events in this SCT.

When the counter is used in bi-directional mode, it is possible to reverse the action specified by 
the output set and clear registers when counting down, See the OUTPUTCTRL register.

0

31:16

-

Reserved

-

Содержание LPC5410x
















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPC5410x

Wang 2236 Product/Maintenance Manual preview
2236
Бренд: Wang Страницы: 68
NAVITAS TSE Series Installation Manual preview
TSE Series
Бренд: NAVITAS Страницы: 14
ICS Tunnel Master Jr User Manual preview
Tunnel Master Jr
Бренд: ICS Страницы: 70
AGRI TRONIX DIGI-STAR GT400 Operator'S Manual preview
DIGI-STAR GT400
Бренд: AGRI TRONIX Страницы: 26
Galcon DC-11SF Installation And Operating Instructions Manual preview
DC-11SF
Бренд: Galcon Страницы: 24
NXP Semiconductors freescale Kinetics TWR-K60N512-KEIL Quick Start Manual preview
freescale Kinetics TWR-K60N512-KEIL
Бренд: NXP Semiconductors Страницы: 5
SECO-LARM ENFORCER SLI PR-B1124-PQ Additional Information preview
ENFORCER SLI PR-B1124-PQ
Бренд: SECO-LARM Страницы: 2
ULTRAFRYER Ultrastat 23 Programming Manual preview
Ultrastat 23
Бренд: ULTRAFRYER Страницы: 1
Oase StreamMax Pump Controller Operating Instructions Manual preview
StreamMax Pump Controller
Бренд: Oase Страницы: 142
DELTA DORE TYBOX 1010 WT User Manual preview
TYBOX 1010 WT
Бренд: DELTA DORE Страницы: 9
Salus Multi-Mix Operation And Installation Manual preview
Multi-Mix
Бренд: Salus Страницы: 40
JBL LED SOLAR CONTROL WIFI Quick Manual preview
LED SOLAR CONTROL WIFI
Бренд: JBL Страницы: 16
Elmo Gold Lion 100 Installation Manual preview
Gold Lion 100
Бренд: Elmo Страницы: 30
WiTi 326-1 Operations & Installation Manual preview
326-1
Бренд: WiTi Страницы: 8
Garmin GRID 20 Installation Instructions preview
GRID 20
Бренд: Garmin Страницы: 4
Id Quantique SWISS QUANTUM+ Time Controller Series User Manual preview
SWISS QUANTUM+ Time Controller Series
Бренд: Id Quantique Страницы: 92
Addonics Technologies ADN1GPX Specification & Installation Manual preview
ADN1GPX
Бренд: Addonics Technologies Страницы: 1
Quick-Ohm QC-PC-CO-CH1 User Manual preview
QC-PC-CO-CH1
Бренд: Quick-Ohm Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды