manualshive.com logo in svg

NXP Semiconductors LPC5410x, Руководство пользователя

Микроконтроллеры NXP Semiconductors LPC5410x - мощные устройства для встроенных систем. Инструкция пользователя доступна для свободного скачивания на manualshive.com. Получите полный контроль над вашим устройством, загрузив бесплатный руководство пользователя.

Поделиться
Скачать
background image

UM10850

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 2.4 — 13 September 2016 

178 of 464

NXP Semiconductors

UM10850

Chapter 13: LPC5410x SCTimer/PWM (SCT0)

13.6.2 SCT configuration register

This register configures the overall operation of the SCT. Write to this register before any 
other registers. Only word-writes are permitted to this register. Attempting to write a 
half-word value results in a bus error.

 

Table 210. SCT configuration register (CONFIG, address 0x5000 4000) bit description 

Bit

Symbol

Value

Description

Reset 
value

0

UNIFY

SCT operation

0

0

The SCT operates as two 16-bit counters named COUNTER_L and 
COUNTER_H.

1

The SCT operates as a unified 32-bit counter.

2:1

CLKMODE

SCT clock mode

0

0x0

System Clock Mode. The system clock clocks the entire SCT module including 
the counter(s) and counter prescalers.

0x1

Sampled System Clock Mode. The system clock clocks the SCT module, but the 
counter and prescalers are only enabled to count when the designated edge is 
detected on the input selected by the CKSEL field. The minimum pulse width on 
the selected clock-gate input is 1 bus clock period. This mode is the 
high-performance, sampled-clock mode.

0x2

SCT Input Clock Mode. The input/edge selected by the CKSEL field clocks the 
SCT module, including the counters and prescalers, after first being 
synchronized to the system clock. The minimum pulse width on the clock input is 
1 bus clock period. This mode is the low-power, sampled-clock mode.

0x3

Asynchronous Mode. The entire SCT module is clocked directly by the 
input/edge selected by the CKSEL field. In this mode, the SCT outputs are 
switched synchronously to the SCT input clock - not the system clock. The input 
clock rate must be at least half the system clock rate and can be the same or 
faster than the system clock.

6:3

CKSEL

SCT clock select. The specific functionality of the designated input/edge is 
dependent on the CLKMODE bit selection in this register.

0

0x0

Rising edges on input 0.

0x1

Falling edges on input 0.

0x2

Rising edges on input 1.

0x3

Falling edges on input 1.

0x4

Rising edges on input 2.

0x5

Falling edges on input 2.

0x6

Rising edges on input 3.

0x7

Falling edges on input 3.

7

NORELAOD_L

-

A 1 in this bit prevents the lower match registers from being reloaded from their 
respective reload registers. Setting this bit eliminates the need to write to the 
reload registers MATCHREL if the match values are fixed. Software can write to 
set or clear this bit at any time. This bit applies to both the higher and lower 
registers when the UNIFY bit is set.

0

8

NORELOAD_H

-

A 1 in this bit prevents the higher match registers from being reloaded from their 
respective reload registers. Setting this bit eliminates the need to write to the 
reload registers MATCHREL if the match values are fixed. Software can write to 
set or clear this bit at any time. This bit is not used when the UNIFY bit is set.

0

Содержание LPC5410x
















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPC5410x

LANGER EMV-Technik E 1 User Manual preview
E 1
Бренд: LANGER EMV-Technik Страницы: 48
Koer C35CBMS Manual preview
C35CBMS
Бренд: Koer Страницы: 6
+GF+ EA15 Instruction Manual preview
EA15
Бренд: +GF+ Страницы: 3
AAF MicroTech II UV05 Operation & Maintenance Manual preview
MicroTech II UV05
Бренд: AAF Страницы: 50
Magicfx FX-COMM4NDER MFX3203 User And Installation Manual preview
FX-COMM4NDER MFX3203
Бренд: Magicfx Страницы: 16
Vexve Hydrox Series Installation, Operation And Maintenance Manual preview
Hydrox Series
Бренд: Vexve Страницы: 24
Tescom RM2020 Installation And User Manual preview
RM2020
Бренд: Tescom Страницы: 15
D+H DXD 150-K-BSY+ Original Instructions Manual preview
DXD 150-K-BSY+
Бренд: D+H Страницы: 20
Rain Bird AESPLX16SM Installation, Connection And Settings preview
AESPLX16SM
Бренд: Rain Bird Страницы: 20
Samson 46-5 Mounting And Operating Instructions preview
46-5
Бренд: Samson Страницы: 24
YOKOGAWA UT32A-C Operation Manual preview
UT32A-C
Бренд: YOKOGAWA Страницы: 10
Danfoss AK-PC 772A User Manual preview
AK-PC 772A
Бренд: Danfoss Страницы: 118
Jordan Valve Mark 60 Series Installation & Maintenance Instructions preview
Mark 60 Series
Бренд: Jordan Valve Страницы: 5
Broan VBATHW Installation And User Manual preview
VBATHW
Бренд: Broan Страницы: 2
Danfoss AK-PC 420 Instructions Manual preview
AK-PC 420
Бренд: Danfoss Страницы: 18
Zaber T-CON3 User Manual preview
T-CON3
Бренд: Zaber Страницы: 23
NXP Semiconductors MPC57xx Application Note preview
MPC57xx
Бренд: NXP Semiconductors Страницы: 11
Beckhoff CU8880-0010 Installation And Operating Instructions Manual preview
CU8880-0010
Бренд: Beckhoff Страницы: 15

Бренды по названию

Популярные бренды

Загрузить еще бренды