manualshive.com logo in svg

NXP Semiconductors LPC43Sxx, Руководство пользователя

Поделиться
Скачать
NXP Semiconductors LPC43Sxx Скачать руководство пользователя страница 1281

UM10503

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2015. All rights reserved.

User manual

Rev. 2.1 — 10 December 2015 

1281 of 1441

NXP Semiconductors

UM10503

Chapter 46: LPC43xx/LPC43Sxx I2C-bus interface

46.5.1 I

2

C Fast-mode Plus

Fast-Mode Plus supports a 1 Mbit/sec transfer rate to communicate with the I

2

C-bus 

products which NXP Semiconductors is now providing. 

In order to use Fast-Mode Plus, the I

2

C pins must be properly configured in the SFSI2C0 

register in the SYSCON block (see 

Table 196

). 

46.6 Pin description

 

The I

2

C-bus pins must be configured through SYSCON registers for Standard/ Fast-mode 

or Fast-mode Plus. 

46.7 Register description

 

Table 1082.I

2

C-bus pin description

Pin function

Type

Description

I2C0_SDA

Input/Output

I

2

C data input/output. Open-drain output (for I

2

C-bus 

compliance).

I2C0_SCL

Input/Output

I

2

C clock input/output. Open-drain output (for I

2

C-bus 

compliance).

I2C1_SDA

Input/Output

I

2

C Serial Data. Uses standard I/O pins (Fast-mode only).

I2C1_SCL

Input/Output

I

2

C Serial Clock. Uses standard I/O pins (Fast-mode only).

Table 1083.Register overview: I

2

C0 (base address 0x400A 1000) 

Name

Access Address 

offset

Description

Reset 
value

[1]

Reference

CONSET

R/W

0x000 

I2C Control Set Register.

 When a one is written to a bit of 

this register, the corresponding bit in the I

2

C control register is 

set. Writing a zero has no effect on the corresponding bit in 
the I

2

C control register.

0x00

Table 1085

STAT

RO

0x004 

I2C Status Register.

 During I

2

C operation, this register 

provides detailed status codes that allow software to 
determine the next action needed.

0xF8

Table 1086

DAT

R/W

0x008 

I2C Data Register.

 During master or slave transmit mode, 

data to be transmitted is written to this register. During master 
or slave receive mode, data that has been received may be 
read from this register.

0x00

Table 1087

ADR0

R/W

0x00C 

I2C Slave Address Register 0.

 Contains the 7-bit slave 

address for operation of the I

2

C interface in slave mode, and 

is not used in master mode. The least significant bit 
determines whether a slave responds to the General Call 
address.

0x00

Table 1088

SCLH

R/W

0x010 

SCH Duty Cycle Register High Half Word.

 Determines the 

high time of the I

2

C clock.

0x04

Table 1089

SCLL

R/W

0x014 

SCL Duty Cycle Register Low Half Word.

 Determines the 

low time of the I

2

C clock. SCLL and SCLH together determine 

the clock frequency generated by an I

2

C master and certain 

times used in slave mode.

0x04

Table 1090

Содержание LPC43Sxx


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды