manualshive.com logo in svg

NXP Semiconductors LPC1311, Руководство пользователя, Страница: 42 / 368

Поделиться
Скачать
NXP Semiconductors LPC1311 Скачать руководство пользователя страница 42

UM10375

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2011. All rights reserved.

User manual

Rev. 3 — 14 June 2011 

42 of 368

NXP Semiconductors

UM10375

Chapter 3: LPC13xx System configuration

 

3.8 Brown-out detection

The LPC13xx includes four levels for monitoring the voltage on the V

DD

 pin. If this voltage 

falls below one of the four selected levels, the BOD asserts an interrupt signal to the 
NVIC. This signal can be enabled for interrupt in the Interrupt Enable Register in the NVIC 
in order to cause a CPU interrupt; if not, software can monitor the signal by reading a 
dedicated status register. Oneadditional threshold level can be selected to cause a forced 
reset of the chip on the LPC1311/13/42/43 parts. Four additional threshold levels for 
forced reset can be selected on the LPC1311/01 and LPC1313/01 parts.

3.9 Power management

The LPC13xx support a variety of power control features. In Active mode, when the chip is 
running, power and clocks to selected peripherals can be optimized for power 
consumption. In addition, there are three special modes of processor power reduction: 
Sleep mode, Deep-sleep mode, and Deep power-down mode. 

Remark: 

The Debug mode is not supported in Sleep, Deep-sleep, or Deep power-down 

modes.

Fig 4.

Start-up timing

valid threshold

 = 1.8V

processor status

V

DD

IRC status

RESET

GND

80 

μ

s

101 

μ

s

boot time

user code

boot code

execution

finishes; 

user code starts

IRC

starts

supply ramp-up

time

55 

μ

s

Содержание LPC1311

















































































































































































































































































































































































Отзывы:

Нет отзывов