NXP Semiconductors LPC11U1x Скачать руководство пользователя | Manualshive

Страница: 260 / 523

background image

UM10462

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 5.5 — 21 December 2016

260 of 523

NXP Semiconductors

UM10462

Chapter 12: LPC11U3x/2x/1x USART

12.5.14 USART Fractional Divider Register

The USART Fractional Divider Register (FDR) controls the clock pre-scaler for the baud
rate generation and can be read and written at the user’s discretion. This pre-scaler takes
the APB clock and generates an output clock according to the specified fractional
requirements.

Important:

If the fractional divider is active (DIVADDVAL > 0) and DLM = 0, the value of

the DLL register must be 3 or greater.

This register controls the clock pre-scaler for the baud rate generation. The reset value of
the register keeps the fractional capabilities of USART disabled making sure that USART
is fully software and hardware compatible with USARTs not equipped with this feature.

The USART baud rate can be calculated as:

(3)

Where UART_PCLK is the peripheral clock, DLM and DLL are the standard USART baud
rate divider registers, and DIVADDVAL and MULVAL are USART fractional baud rate
generator specific parameters.

The value of MULVAL and DIVADDVAL should comply to the following conditions:

1. 1



MULVAL



15

2. 0



DIVADDVAL



14

3. DIVADDVAL< MULVAL

The value of the FDR should not be modified while transmitting/receiving data or data may
be lost or corrupted.

If the FDR register value does not comply to these two requests, then the fractional divider
output is undefined. If DIVADDVAL is zero then the fractional divider is disabled, and the
clock will not be divided.

Table 247. USART Fractional Divider Register (FDR - address 0x4000 8028) bit description

Bit

Function

Description

Reset
value

3:0

DIVADDVAL

Baud rate generation pre-scaler divisor value. If this field is 0,
fractional baud rate generator will not impact the USART baud
rate.

0

7:4

MULVAL

Baud rate pre-scaler multiplier value. This field must be greater
or equal 1 for USART to operate properly, regardless of whether
the fractional baud rate generator is used or not.

1

31:8

-

Reserved, user software should not write ones to reserved bits.
The value read from a reserved bit is not defined.

0

UART

baudrate

PCLK

16

256

U0DLM



U0DLL

+







1

DivAddVal

MulVal

-----------------------------

+











----------------------------------------------------------------------------------------------------------------------------------

=

«
...
258
259
260
261
262
...
»

Содержание LPC11U1x












































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPC11U1x

Бренд: Facility Explorer Страницы: 4

Бренд: Aalborg Страницы: 48

MachXO5-NX Development Kit

Бренд: Lattice Semiconductor Страницы: 2

Бренд: Eaton Страницы: 8

Бренд: AirCycler Страницы: 2

Torque Converter Lock-Up

Бренд: TS Performance Страницы: 4

multicomp F144-MS-1V1C1TI6RO-3

Бренд: KBR Страницы: 68

EZ-ZONE PM L AAAAB Series

Бренд: Watlow Страницы: 30

Бренд: OCL Страницы: 2

AMP 3K/40 CE 2161600-1

Бренд: TE Connectivity Страницы: 29

Бренд: H3C Страницы: 15

Бренд: Hanbay Страницы: 13

SetPro MV Series

Бренд: Gigarise Страницы: 18

Alicat Scientific IVCD

Бренд: Halma Страницы: 28

Бренд: Cablematic Страницы: 6

Бренд: Delta Страницы: 313

Бренд: Dontek Страницы: 2

Бренд: Mitsubishi Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды