NXP Semiconductors KITPF5200SKTEVM Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 51

NXP Semiconductors KITPF5200SKTEVM Скачать руководство пользователя страница 30

NXP Semiconductors

UM11636

KITPF5200SKTEVM evaluation board

4. Click

IO PINS

button in the Tools access bar. When the IO PINS window appears, set

TBBEN high. If TBBEN has already been set high by the MCU, do nothing.

5. Return to the Mirror tool and Read/Write the mirror registers as you require.

6. On the evaluation board, switch SW1 to the On (1) position. The part starts with the

modified settings.

The following figure shows the Configuration tab of the Mirror tool.

Figure 5. Mirror - Configuration tab

5.2.3.3.5 OTP

The OTP tool allows you to enter an OTP configuration and save it as a .cfg file. The .cfg

file is used by the GUI to log all of the configuration information. A TBB file can be

created with a .txt extension. The TBB file can be used either to load the mirror registers

in TBB mode or to burn OTP fuses using the PROG tool.
The OTP configuration is not addressed here. For information on OTP configuration, see

the PF5200 OTP configuration application note.
The main panel of the OTP tool main panel is divided into the four sections shown in

UM11636

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2021. All rights reserved.

User manual

Rev. 2 — 13 December 2021

30 / 51

«
...
28
29
30
31
32
...
»

Содержание KITPF5200SKTEVM




















































Отзывы:

Нет отзывов