NXP Semiconductors KITPF5200FRDMEVM Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 51

NXP Semiconductors KITPF5200FRDMEVM Скачать руководство пользователя страница 43

NXP Semiconductors

UM11723

KITPF5200FRDMEVM evaluation board

6.2 Connecting the PF5200 to the GUI

The procedure for connecting the PF5200 to the GUI is as follows:
1. Click the Windows icon at the bottom left of the screen and select NXPGUI icon to

open the GUI.

2. When the GUI opens, the Kit Selection window appears. Select PF5200 and click

OK

. Note: If the File menu shows a check mark next to the "Do not display GUI Kit

selection at Start" item, the Kit Selection window does not appear at start-up.

3. In the bar at the bottom of the window, the State message should display

"DISCONNECTED". This indicates that the USB cable is plugged in but

communication has not yet been established between the FRDM-KL25Z and the

UM11723

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2021. All rights reserved.

User manual

Rev. 1 — 8 December 2021

43 / 51

«
...
41
42
43
44
45
...
»

Содержание KITPF5200FRDMEVM




















































Отзывы:

Нет отзывов