manualshive.com logo in svg

NXP Semiconductors K22F series, Справочное руководство, Страница: 1189 / 1407

Поделиться
Скачать
NXP Semiconductors K22F series Скачать руководство пользователя страница 1189

I2Cx_S field descriptions (continued)

Field

Description

0

Bus is idle

1

Bus is busy

4

ARBL

Arbitration Lost

This bit is set by hardware when the arbitration procedure is lost. The ARBL bit must be cleared by
software, by writing 1 to it.

0

Standard bus operation.

1

Loss of arbitration.

3

RAM

Range Address Match

This bit is set to 1 by any of the following conditions, if I2C_C2[RMEN] = 1:

• Any nonzero calling address is received that matches the address in the RA register.
• The calling address is within the range of values of the A1 and RA registers.

NOTE: For the RAM bit to be set to 1 correctly, C1[IICIE] must be set to 1.

Writing the C1 register with any value clears this bit to 0.

0

Not addressed

1

Addressed as a slave

2

SRW

Slave Read/Write

When addressed as a slave, SRW indicates the value of the R/W command bit of the calling address sent
to the master.

0

Slave receive, master writing to slave

1

Slave transmit, master reading from slave

1

IICIF

Interrupt Flag

This bit sets when an interrupt is pending. This bit must be cleared by software by writing 1 to it, such as in
the interrupt routine. One of the following events can set this bit:

• One byte transfer, including ACK/NACK bit, completes if FACK is 0. An ACK or NACK is sent on the

bus by writing 0 or 1 to TXAK after this bit is set in receive mode.

• One byte transfer, excluding ACK/NACK bit, completes if FACK is 1.
• Match of slave address to calling address including primary slave address, range slave address,

alert response address, second slave address, or general call address.

• Arbitration lost
• In SMBus mode, any timeouts except SCL and SDA high timeouts
• I2C bus stop or start detection if the SSIE bit in the Input Glitch Filter register is 1

NOTE:

To clear the I2C bus stop or start detection interrupt: In the interrupt service
routine, first clear the STOPF or STARTF bit in the Input Glitch Filter register by
writing 1 to it, and then clear the IICIF bit. If this sequence is reversed, the IICIF
bit is asserted again.

0

No interrupt pending

1

Interrupt pending

0

RXAK

Receive Acknowledge

0

Acknowledge signal was received after the completion of one byte of data transmission on the bus

1

No acknowledge signal detected

Chapter 46 Inter-Integrated Circuit (I2C)

K22F Sub-Family Reference Manual, Rev. 4, 08/2016

NXP Semiconductors

1189

Содержание K22F series
































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов