NXP Semiconductors i.MX 8M Plus LPDDR4 EVK Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 20

NXP Semiconductors i.MX 8M Plus LPDDR4 EVK Скачать руководство пользователя страница 4

Table 1. Board features (continued)

Audio connector

3.5 mm Audio jack for Headset

Debug connector

JTAG (10pin header)

Micro-B USB for UART debug (Two COM Ports for A53 and M7) and remote debug of JTAG,
Bootmode, ONOFF, SYS_nRST, and Power Measurement Board communication.

Expansion connector

40-pin dual-row Pin Header for I2S, UART, I2C and GPIO expansion

I2C connector

8-pin dual-row Pin Header for I

2

C expansion

Buttons

ON/OFF, RESET

LED indicators

Power status, UART

PCB

8MPLUSLPD4-CPU: 2.3 inch × 2.3 inch, 6-layer
8MPLUS-BB: 6 inch × 8.26 inch, 8-layer

1.2 Board contents

The i.MX 8M Plus LPDDR4 EVK contains the following items:

• i.MX 8M Plus LPDDR4 EVK board, assembled by two separate boards, 8MPLUSLPD4-CPU (CPU Board) and 8MPLUS-

BB (Base Board)

• USB Type-C 45W Power Delivery Supply, 5V/3A, 9V/3A, 15V/3A, 20V/2.25A supported
• USB Type-C Cable, Cable – Assembly, USB 3.0, Type-C Male to Type-A Male
• USB micro-B Cable, Cable – Assembly, USB 2.0, Type-B Male to Micro-A Male
• USB Type-C to Type-A Adapter, Adapter – USB 3.0, Type-C Male to Type-A Female
• Quick Start Guide

NXP Semiconductors

Introduction

i.MX 8M Plus LPDDR4 EVK Board Hardware User's Guide, Rev. 0, March 9, 2021

User's Guide

4 / 20

«
...
2
3
4
5
6
...
»

Содержание i.MX 8M Plus LPDDR4 EVK





















Отзывы:

Нет отзывов