NXP Semiconductors freescale KV4 Series Скачать руководство пользователя | Manualshive

Страница: 671 / 1359

background image

ADC_CTRL1 field descriptions (continued)

Field

Description

0

DMA is not enabled.

1

DMA is enabled.

14

STOP0

Stop

When this bit is asserted, the current scan is stopped and no further scans can start. Any further SYNC0
input pulses (see CTRL1[SYNC0] bit) or writes to the CTRL1[START0] bit are ignored until this bit has
been cleared. After the ADC is in stop mode, the results registers can be modified by the processor. Any
changes to the result registers in stop mode are treated as if the analog core supplied the data. Therefore,
limit checking, zero crossing, and associated interrupts can occur when authorized.

This is not the same

as DSP STOP mode.

0

Normal operation

1

Stop mode

13

START0

START0 Conversion

A scan is started by writing 1 to this bit. This is a write only bit. Writing 1 to it again while the scan remains
in process, is ignored.

The ADC must be in a stable power configuration prior to writing the start bit. Refer to the functional
description of power modes for further details.

0

No action

1

Start command is issued

12

SYNC0

SYNC0 Enable

A conversion may be initiated by asserting a positive edge on the SYNC0 input. Any subsequent SYNC0
input pulses while the scan remains in process are ignored unless the scan is awaiting further SYNC
inputs due to the SCTRL[SCn] bits. CTRL1[SYNC0] is cleared in ONCE mode, CTRL1[SMODE=000 or
001], when the first SYNC input is detected. This prevents unintentionally starting a new scan after the first
scan has completed.

The ADC must be in a stable power mode prior to SYNC0 input assertion. Refer to the functional
description of power modes for further details.

In "once" scan modes, only a first SYNC0 input pulse is honored. CTRL1[SYNC0] is cleared in this mode
when the first SYNC input is detected. This prevents unintentionally starting a new scan after the first scan
has completed. The CTRL1[SYNC0] bit can be set again at any time including while the scan remains in
process

0

Scan is initiated by a write to CTRL1[START0] only

1

Use a SYNC0 input pulse or CTRL1[START0] to initiate a scan

11

EOSIE0

End Of Scan Interrupt Enable

This bit enables an EOSI0 interrupt to be generated upon completion of the scan. For looping scan
modes, the interrupt will trigger after the completion of each iteration of the loop.

0

Interrupt disabled

1

Interrupt enabled

10

ZCIE

Zero Crossing Interrupt Enable

This bit enables the zero crossing interrupt if the current result value has a sign change from the previous
result as configured by the ZXCTRL1 and ZXCTRL2 registers.

0

Interrupt disabled

1

Interrupt enabled

Table continues on the next page...

Chapter 34 12-bit Cyclic Analog-to-Digital Converter (ADC)

KV4x Reference Manual, Rev. 2, 02/2015

Freescale Semiconductor, Inc.

Preliminary

671

«
...
669
670
671
672
673
...
»

Содержание freescale KV4 Series
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для freescale KV4 Series

Бренд: OEG Страницы: 168

Бренд: Accel Страницы: 8

Бренд: Maestra Страницы: 22

Бренд: Quantum Страницы: 20

LDSBus LC020101A-F

Бренд: BRT Systems Страницы: 15

Бренд: GeoVision Страницы: 21

Бренд: Altronix Страницы: 8

Бренд: nvent Страницы: 6

Бренд: Teledyne Страницы: 47

Бренд: Western Co Страницы: 14

Бренд: EpiSensor Страницы: 37

Бренд: Datakom Страницы: 34

Бренд: Hotone Страницы: 2

Бренд: Infineon Technologies Страницы: 677

Бренд: Murphy Страницы: 16

AK-CC 750 series

Бренд: Danfoss Страницы: 96

Бренд: YASKAWA Страницы: 25

Бренд: Berkeley Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды