NXP Semiconductors freescale KV4 Series Скачать руководство пользователя | Manualshive

Страница: 432 / 1359

background image

• Internal SRAM can be accessed with zero wait-states when viewed from the system

bus data phase

• All internal peripheral bus reads require two wait-states, and internal peripheral bus

writes three wait-states, when viewed from the system bus data phase

• All internal peripheral bus accesses are 32-bits in size

NOTE

All architectures will not meet the assumptions listed above.
See the SRAM configuration section for more information.

This table compares peak transfer rates based on different possible system speeds.
Specific chips/devices may not support all system speeds listed.

Table 23-293. eDMA peak transfer rates (Mbytes/sec)

System Speed, Width

Internal SRAM-to-

Internal SRAM

32 bit internal peripheral

bus-to-Internal SRAM

Internal SRAM-to-32 bit

internal peripheral bus

66.7 MHz, 32 bit

133.3

66.7

53.3

83.3 MHz, 32 bit

166.7

83.3

66.7

100.0 MHz, 32 bit

200.0

100.0

80.0

133.3 MHz, 32 bit

266.7

133.3

106.7

150.0 MHz, 32 bit

300.0

150.0

120.0

Internal-SRAM-to-internal-SRAM transfers occur at the core's datapath width. For all
transfers involving the internal peripheral bus, 32-bit transfer sizes are used. In all cases,
the transfer rate includes the time to read the source plus the time to write the destination.

23.4.4.2 Peak request rates

The second performance metric is a measure of the number of DMA requests that can be
serviced in a given amount of time. For this metric, assume that the peripheral request
causes the channel to move a single internal peripheral bus-mapped operand to/from
internal SRAM. The same timing assumptions used in the previous example apply to this
calculation. In particular, this metric also reflects the time required to activate the
channel.

The eDMA design supports the following hardware service request sequence. Note that
the exact timing from Cycle 7 is a function of the response times for the channel's read
and write accesses. In the case of an internal peripheral bus read and internal SRAM
write, the combined data phase time is 4 cycles. For an SRAM read and internal
peripheral bus write, it is 5 cycles.

Functional description

KV4x Reference Manual, Rev. 2, 02/2015

432

Preliminary

Freescale Semiconductor, Inc.

«
...
430
431
432
433
434
...
»

Содержание freescale KV4 Series
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для freescale KV4 Series

Бренд: 3Ware Страницы: 2

Elemec3 013-02-0095-002

Бренд: GAI-Tronics Страницы: 12

Бренд: L. G. B. Страницы: 2

Бренд: L-Acoustics Страницы: 36

Бренд: OES Страницы: 3

Бренд: Centurion Страницы: 16

Бренд: W.E.ST. Страницы: 34

Бренд: Ltech Страницы: 4

Бренд: Motor Guard Страницы: 2

ADAP-KOOL AK-PC 781

Бренд: Danfoss Страницы: 142

ERO-32AP-0 V1.4

Бренд: Darco Страницы: 14

Бренд: Rainmachine Страницы: 22

Бренд: Galcon Страницы: 24

freescale Kinetics TWR-K60N512-KEIL

Бренд: NXP Semiconductors Страницы: 5

ENFORCER SLI PR-B1124-PQ

Бренд: SECO-LARM Страницы: 2

Бренд: ULTRAFRYER Страницы: 1

Бренд: X10 Страницы: 3

Бренд: Zaber Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды