NXP Semiconductors Freescale KIT33905 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 22

NXP Semiconductors Freescale KIT33905 Скачать руководство пользователя страница 11

KIT33905 Evaluation Boards

, Rev. 2.0

Freescale Semiconductor

11

Using the EVB

7

Using the EVB

1. Select Install SPIGen (setup.exe) from the CD33905 Start page and follow the on-screen installation

instructions.

2. Connect power supply to the VBAT and GND terminals on the EVB and build the setup as shown on

3. Ensure the voltages provided are in accordance with the device data sheet and that the supply

currents are sufficient to supply the device.

4. To use SPIGen, go to the Windows

Start

menu >

Programs

>

SPIGen

and click on the

SPIGen

icon.

The

SPIGen Generic SPI Generator

GUI will appear.

5. Go to the

Configure

menu in the upper left hand corner of the GUI and select

Edit Configuration

.

6. Select the

Enable 33905 Tab

in the

Part Specific Tabs

section on the lower right hand corner of the

GUI and click

OK

button.

7. Select the

SBC MC3390x Family

tab.

7.1

Using SPIGen with the MC33905 Product

Evaluating all capabilities of the MC33905 product is made easy with the included SPIGen and respective

GUI configuration file.

«
...
9
10
11
12
13
...
»

Содержание Freescale KIT33905























Отзывы:

Нет отзывов