Nvidia Jetson AGX Xavier Series Скачать руководство пользователя | Manualshive

Страница: 56 / 157

background image

USB, PCIe, and UFS

Jetson AGX Xavier Series Product

DG-09840-001_v2.5 | 41

7.1

USB

Jetson AGX Xavier supports up to four USB 2.0 ports and up to three USB 3.1 ports. There are
examples in this section to either implement a simple USB 3.1/2.0 connection to a USB 3.1
Type A connector or to replicate the USB Type C connections used on the NVIDIA Developer
Kit. Designs that intend to follow the NVIDIA Developer Kit carrier board design and include
the Type C PD Controller (CYPD4226) need to replicate the circuitry on the latest P2822 carrier
board exactly. NVIDIA will provide the binary and the customer should get the flashing
instructions from Cypress. If the design requires a simpler solution (Type A or similar), then
refer to the software adaptation guide for information.

Notes

:

•

Some non-compliant USB 3.1 devices may fail unless USB 3.1 Gen2 is disabled.

•

See Section 15.1

“USB Recover Mode” for requirements for USB recovery mode.

Figure 7-1.

Simple USB Type A Connection Example

Jetson AGX Xavier

SoC

USB 2.0

USB 3.1

PCIe

UFS

USB1_DP

USB1_DN

C11
C10

PEX_TX6_P

PEX_TX6_N

PEX_RX6_P

PEX_RX6_N

K17
K16
B16
B17

GPIO22

USB1_P
USB1_N

UPHY_TX6_P
UPHY_TX6_N

UPHY_RX6_P
UPHY_RX6_N

USB 3.1

Type A

VBUS

TX+

D+

D–

TX–
RX+

RX–

ESD

Load Switch

EN

OC

IN

OUT

VDD_5V0

Common

Mode Choke

0.1uF

0.1uF

Common

Mode Choke

100Ω

UART

USB_VBUS_EN0

F54

USB_VBUS_EN0

Type C connections are based on the NVIDIA carrier board design. Additional interface
assignments shown in Figure 7-2 are also based on the carrier board usage.
Designs that intend to follow the NVIDIA carrier board design and include the Type C PD
Controller (CYPD4226 - U513 on NVIDIA carrier board) need to replicate the circuitry on the
latest P2822 carrier board exactly. NVIDIA will provide the binary and the customer should get
the flashing instructions from Cypress.
If the CYPD4226 PD controller is implemented in a design, it is recommended that test points
be included that connect to the

SW_CLK, SW_IO

and

XRES

pins as well as

VDD_AO

. These would be

required to flash the binary during manufacturing.

«
...
54
55
56
57
58
...
»

Содержание Jetson AGX Xavier Series






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Jetson AGX Xavier Series

Бренд: PaloAlto Networks Страницы: 3

AIE900-XNX Series

Бренд: AXIOMTEK Страницы: 53

Бренд: Barco Страницы: 30

Бренд: Sangoma Страницы: 6

Бренд: PMD Страницы: 74

RanaSystems 13-0010--001

Бренд: RANA Systems Страницы: 328

Бренд: SYNTEK Страницы: 41

Бренд: INNOSILICON Страницы: 11

Бренд: NZXT Страницы: 2

Бренд: Magma Страницы: 2

Бренд: Cypress Semiconductor Страницы: 15

Бренд: SriHome Страницы: 12

HFisolator 9730/26-11

Бренд: Stahl Страницы: 2

Бренд: Smacq Technologies Страницы: 22

LL140 RGB Series

Бренд: Corsair Страницы: 30

Бренд: ADLINK Technology Страницы: 108

Бренд: ICP DAS USA Страницы: 8

Бренд: Roland Страницы: 224

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды