manualshive.com logo in svg

nvent Erico Ericore, Инструкция, Страница: 8 / 11

Поделиться
Скачать
nvent Erico Ericore Скачать руководство пользователя страница 8

AT LEAST 30 MM OVERLAP

(B)

(A)

Then place the second 450 mm (17 3/4 in) length of heatshrink tube (10) into place over the 

cable, overlapping the previous heatshrink tube. Start shrinking at the top brass fitting end, 

and shrink it so that the lower brass nut is just covered as shown in Figure 10b. 

Continue heating until it shrinks over the first piece.

Figure 9:

 Applying the first layer of heatshrink

Figure 10:

 Applying the second layer of heatshrink

Figure 11:

 Finished heatshrink assembly

21.

 Installing the Heatshrink

There are two lengths of heatshrink in this kit (one is 900 mm (35 1/2 in) long, the other is 

450 mm (17 1/2 in) long). Slide on and heat both in the manner shown.

Slide the first 900 mm (35 1/2 in) length of heatshrink (9) over the cable until the end of the 

heatshrink tube covers and overlaps the semi-conductive tape (over the black outer sheath) 

at the bottom end by at least 30 mm (1 1/8 in). The braid will protrude from under the 

heatshrink at this point. Use the desktop or handheld heatshrink gun (8) to carefully shrink 

the lower end of the heatshrink into the correct position (with the braid protruding) and 

gradually work up towards the top of the heatshrink ensuring there are no pockets of air 

trapped under the heatshrink.

IP8519_A

8 OF 11

INSTRUCTION SHEET



© 2019 nVent All Rights Reserved

TECHNICAL SUPPORT

www.nVent.com

nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are owned by nVent or its 

global affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change 

specifications without prior notice.

Содержание Erico Ericore












Отзывы:

Нет отзывов