manualshive.com logo in svg

nvent Erico Ericore, Инструкция, Страница: 7 / 11

Поделиться
Скачать
nvent Erico Ericore Скачать руководство пользователя страница 7

18. 

Install the main coupler over the strands.Do 

not force the main coupler on as it should slide 

on smoothly. 

Cut and remove both zip ties

. 

19. 

Thread main coupler into the the 

compression coupler. Tighten both couplers 

together with the shifting spanner/wrench (3).

20. 

Starting immediately at the end of the 

compression coupler, wrap the remaining semi-

conductive tape (18) around and over the 

copper tape, covering it completely, then 

extending an additional 40 mm (1 1/2 in) over 

the triple layer insulation with an overlap on 

each turn.

(18)

(18)

(19)

(19)

(20)

(20)

IP8519_A

7 OF 11

INSTRUCTION SHEET



© 2019 nVent All Rights Reserved

TECHNICAL SUPPORT

www.nVent.com

nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are owned by nVent or its 

global affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change 

specifications without prior notice.

Содержание Erico Ericore












Отзывы:

Нет отзывов