Button
Function
Use
Turns the Infinity
™
Blender on and off.
Turn the red main Base Power Switch ON. Switch is located on the right side of Blender Base.
Press
Power
button once to turn your Infinity
™
Blender on. Press the
Power
button again and
press the red main Base Power Switch OFF to turn your Infinity Blender
™
off.
Start/Pause
Starts and pauses the cooking process,
and allows you to clear any selections.
Turn the dial to choose your appropriate blending function. Press
Start/Pause
to start
blending. Press
Start/Pause
again to stop blending.
Note:
Do not fill Jar above ¾ capacity.
For best results, do not fill more than 1.5 liters (51 fl oz) of liquid. Refer to
“Instructions”
in
the owner’s manual.
Time
Set your time. Press the up and down
arrows to increase or decrease the time on
the display.
Times are displayed in minutes and seconds. Adjustments can be made on all settings.
Note:
When blending for a long period of time, liquids may become hot and steam may escape from
the Plunger Cap.
Number
Settings
Use the numbered settings. Default time is
3 minutes
For standard blending you can select from one of the numbered speed settings between 1 and
10. Adjust to desired time, then press
Start/Pause
to begin blending.
Note:
The lowest setting
is #1 (5,000 RPM). The highest setting is #10 (17,000 RPM).
Icons
Icon settings are for specialized blending
tasks. Each icon setting has default time
and RPM built in.
Turn the dial to desired icon setting and press
Start/Pause
to begin blending.
Note:
Always
start with cold liquids when blending. DO NOT add hot liquids to the Infinity
™
Blender. Hold the
Up
and
Down
buttons to move percentage points faster.
Pulse
The Infinity
™
Blender offers two Pulse
functions where the power settings are fully
adjustable.
Press
Pulse 1
for short bursts of blending at low power (25% Power).Press
Pulse
2
for short
bursts of blending at high power (100% Power).
Cleaning
For quick cleaning with soap and water.
Add water and 1-2 drops of liquid dish soap to your Jar, place on the Base, and close the
Lid. Turn the dial to Clean. 00:15 will be shown on the LED display. Adjust the time if desired,
and then press
Start/Pause
. Once finished, remove the Jar, rinse thoroughly, and dry before
using.
Note:
For detailed instructions on cleaning refer to
“Cleaning & Maintenance.”
Quick Start Guide
Getting Started
Refer to the Owner’s Manual for more details
Model No: 28202
©2021 NuWave LLC • All Rights Reserved. • Customer Service: 1-877-689-2838• [email protected]
Model No: 20902 • Item No: BQ20902 • Rev. 2-OG • 12-16-21
Troubleshooting Guide
The Infinity
™
Blender was engineered with an automatic shut-off feature to prevent overheating during use. If the Infinity
™
Blender shuts off to
cool itself down, an odor may be detected. Unplug the Infinity
™
Blender and wait for it to completely cool down. To prevent overheating, do not
process at speeds not recommended.
The Infinity
™
Blender is not turning on or working.
1. Plug may not be in the outlet. Plug in
the
Infinity
™
Blender
into
an appropriate power source.
2.
The
Red Power Switch on right side of Base may not be on.
Check to see if the Power Switch is on.
The
Infinity
™
Blender does not work when plugged in and
Power button and Power Switch are both ON.
Make sure the unit is plugged correctly, try another wall power
outlet. If the problem persists, contact customer service.
The
Infinity
™
Blender is not running at a high enough speed
for the recipe.
1.
The
Dial is not on the correct setting. Turn the
D
ial to proper
setting based on the recipe.
2.
The
Jar is overloaded. Reduce
the
amount of your
ingredients.
The
Infinity
™
Blender becoming clogged and not operating
efficiently.
1. Certain ingredients can cause clogging. When using
the
Plunger Lid, remove
the
Plunger Cap from
the
Lid and insert
the
Plunger through hole. Press
the
ingredients down and
around until mixture loosens around the bottom of
the
Jar.
2. The ingredient amounts higher than specified are being used.
Do not fill the Jar above ¾ capacity (1.5 liters, 51 fl oz).
3.
Large pieces of ice are not mixing properly. Use smaller pieces
of ice.
The b
lended mixture has lumps or
the
texture is not even.
Air pocket has formed (cavitation) and mixture is too cold or has
solidified in areas, and
the
blades are spinning in cavity. Increase
the
temperature by reducing ice in the recipe.
Noises or motions unusual for the normal operation of the
Infinity
™
Blender are detected.
1.
The
Blade assembly may be loose, missing a part, or possibly
damaged. Turn
the
Infinity
™
Blender
OFF and unplug immediately.
DO NOT disassemble
the B
lade assembly. Call Customer Service:
1-877-689-2838 or email [email protected].
2. Foreign objects from ingredients may have been put into
the
Jar and
are making unusual sounds. Prior to adding your ingredients to the
Jar and blending, clean fruits/other ingredients and remove all debris
or any objects.
Error Message:
Solution(s)
Er1
The NTC Temperature Sensor has short circuited.
Contact NuWave Customer Service 1-877-689-2838
Er2
The NTC Temperature Sensor is open. Contact
NuWave Customer Service 1-877-689-2838
Er3
The NTC Sensor has overheated. Turn the Infinity
™
Blender off and allow it to cool. If the Infinity
™
Blender is not working after it cools down, Contact
NuWave Customer Service 1-877-689-2838 or
I N F I N I T Y
B L E N D E R
TM
