Menu Key ( )
NUVITA AUDIOVOICE 1098
EN
WARNING!
STRANGULATION HAZARD - Keep the adapter cord out of baby’s reach
IMPORTANT SAFETY INSTRUCTIONS
WARNING
CAUTION!
This baby monitor is not designed to replace responsibility of human supervision
on children.
This baby monitor must be assembled and installed by an adult.
This product is designed for indoor use.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Clean only with dry cloth.
Do not use this baby monitor near water.
Do not install this baby monitor near a heat source.
Do not cover the baby monitor with a towel or blanket.
Unplug this apparatus during lightning storms or when unused for long periods
of time.
The small parts of this baby monitor can be swallowed by babies or small
children.
Keep these parts out of reach of children.
Do not touch the plug contacts with sharp or metal objects.
Protect the power cord from being walked on or pinched, particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
Only use the power adapters provided. Do not use other charges or power
adapters as this may damage the device and battery pack.
Risk of explosion if battery is replaced by an incorrect type. Dispose of used
batteries according to the instructions.
Never place camera or cords within the cot/crib
The baby unit and cables should be at least 3 ft/1 m away from children
Secure the cord to the wall to keep cord away from the baby’s reach
Never use extension cords with AC adapters. Only use the AC adapters
provided
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
PRODUCT AND ACCESSORIES
CONTENTS
Baby unit x1
Parent unit x1
Rechargeable Lithium battery x1
Power adapter for the baby unit x1
(Longer cable one)
Power adapter for the parent unit x1
(shorter cable one)
Screws and extension bolt x2 to mount
baby unit on the wall.
User’s guide x1
OVERVIEW OF THE BABY UNIT
01. Camera lens
05. Speaker
04. Antenna
03. Microphone
02. Photo sensor (Night Vision on/off)
06. On/Off Switch
07. Power adapter connector
08. Power Led
09. Pairing key (for service center use only)
•
•
•
•
•
•
•
OVERVIEW OF THE PARENT UNIT
mode NORMAL
mode ZOOM IN
mode MENU
1
Press to enter/exit
menu
right arrow to move
image to the right
2
press and hold to speak to
your baby
left arrow to move
image to the left
3
4
5
6
7
8
press to zoom in 2X, press again
to go back to 1X
to switch between
menu items
9
Adjust audio level
louder
up arrow to move
image to the top
to switch between
menu items
10
Adjust audio level
lower
down arrow to move
image to the bottom
to switch between
menu items
11
Display (LCD)
VOX Mode LED (green Led)
Speaker
Microphone
Belt clip
Power LED (Power on = steady green; Power low = flashing red)
Talk Key ( )
Zoom key ( )
Volume up ( )
Volume down ( )
13
14
15
16
Battery Cover
Audio level LEDs (blue LEDs)
Power adapter connector
Power On/Off switch ( )
(Press and hold to turn on/off parent units)
12 Stand
SIGNIFICATO DELLE ICONE DEL MENU NELL’UNITÀ GENITORE
Battery level (3 levels plus flashing of battery low)
Signal strength (4 levels)
Talk mode
Night vision mode (Image becomes black/white)
VOX mode (Baby and parent unit are in sleep mode while baby sleeps.
Baby and parent unit will start streaming video and audio when baby cries)
Trigger sensitivity level (3 levels)
Brightness level (5 levels)
Out of range/Lost link alert
Auto mute on/off. Switch auto mute “on”, parent unit enters audio mute mode
automatically when baby does not make much noise. Parent unit starts to
stream audio when baby’s sound level exceeds preset sensitivity level
PLUG IN BABY UNIT POWER ADAPTER
PLUG IN BABY UNIT POWER ADAPTER
• Make sure to use provided (6V 800mA) power adapter, the longer cable one.
•Slide the switch to On position to turn on baby unit. Green power LED is turned on.
GETTING STARTED
Make sure to use provided (6V 800mA) power adapter, the shorter cable one.
Plug in adapter to parent unit to charge parent unit for at least 4 hours before using
the parent unit for the first time.
Press and hold power On/Off key for 2 seconds to turn on parent unit.
Once the baby and parent units are switched on, the display on the parent unit will
show the video captured by the baby unit.
If there is no connection or you are out of range, the video display will go off and
the Lost Link signal will be shown on the LCD display with beep sounds every 3
seconds. Move the parent unit closer to the baby unit until the link is re-established.
OPERATION ON RECHARGEABLE BATTERIES
The parent unit comes with a rechargeable Li-ion polymer rechargeable
battery.
The battery symbol flashes and power LED flash red when battery is empty.
If the battery is completely empty, the parent unit automatically switches off
and loses contact with the baby unit.
The rechargeable battery is inside of the parent unit. If you need replacement
of battery when battery has reached end of life, please follow the following
steps:
Slide open battery compartment lid to remove it.
Insert the rechargeable battery with cable alignment
as shown in figure.
Reattach the lid.
•
•
•
Charging normally takes 2.5 hours, but it takes longer when the parent unit
is switched on during charging. To keep charging time as short as possible,
switch off the parent unit during charging.
When the rechargeable battery is fully charged, the parent unit can be used
approximately 10 hours if the parent unit is on VOX mode.
•
•
