Package
Overview
Installation
1
2
3
4
2
1
3
*
1 It
is
recommended
to
install
the
water
-
proof
cap
for
network
cable connection
.
*
2
If
the
PoE network switch is
used
to
connect
the
camera, DC12V
power supply
is
not
required
.
①
Loosen
the
nut
from
the
main
element.
②
Run
the
network
cable (without
RJ 45
connector) through the
both elements. Then
crimp
the
cable
with
RJ 45
connector
.
③
Connect
the
cable
to
the
hermetic
connector
.
Then
tighten
the
nut
and
the
main
cover
.
Thank you for purchasing our product. There may be several
technically incorrect places or printing errors in this manual.
The updates will be added into the new version of this manual.
We will readily improve or update the products or procedures
described in the manual. The content is subject to change
without notice.
Warning
and
Caution
■
If the product does not work properly, please contact your dealer
or the nearest service center. Never attempt to disassemble the
camera yourself. (We shall not be responsible for any problems
caused by unauthorized repair or maintenance.)
■
Keep away from liquid while in use.
■
In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the
product is mounted on wall or ceiling, the device shall be firmly
fixed.
■
Do
not
use
camera
beyond
specified
voltage
range
.
■
Do not drop the camera or subject it to physical shock.
■
Avoid touching the camera lens.
■
If cleaning is necessary, please use clean cloth to wipe it gently.
If the device will not be used for a long time, please cover the lens
cap to protect the device from dirt.
■
Do not aim the camera at the sun or extra bright place.
■
Do not place the camera in extremely hot, cold (the operating
temperature shall be -20˚C~50˚C), dusty or damp locations, and do
not expose it to high electromagnetism radiation.
■
To avoid heat accumulation, good ventilation is required for
operating environment.
■
A few parts of the device shall be replaced regularly according
to their average enduring time. Regular checking is recommended
for all users.
Please make sure that the wall or ceiling is strong enough to
withstand 3 times the weight of the camera. Please install and use
the camera in the dry environment. You'd better install back the lens
cover less than 4 hours after removing it.
①
Drill the screw holes and the cable hole on the wall according to
the drill template.
②
Route the cables and connect the relevant cables.
Camera
Quick
start
guide
CD
Water
-
proof
cap
Plastic
plug
×4
Drill
template
Rubber
plug
CVBS&DC
IN cables
Screwdriver
4 tapping screws PA4×25
1 machine screw PWM3×5
∅
22.6
∅
91.4
∅
103
∅
5
64.6mm
64.6mm
90°
Microphone Cable
Headphone Cable
TF
Card
Slot
Reset
Hole
CVBS/DC IN port for testing
Alarm Input/Output
RS485 Cable
Network Cable
Power
Cable
1
2
3
5
7
9
4
6
8
10
ALM-COM
ALM-NO
ALM-IN
ALM-GND
RS485T-
N
et
w
or
k C
ab
le
●
Alarm Connection
Alarm Input
: Join the grounding ends of the sensor and the camera
and then connect the signal cable of the sensor to the alarm input
port of the camera.
Alarm Output
: Loosen the screws in the alarm output port. Then
insert the signal wires of the alarm output devices into the port of
NO and COM separately. Finally tighten the screws. Some of the
external alarm output devices need the power supply.
●
Connecting
Network
Cable
8
9
10
2
3
4
5
6
1
7
CVBS Cable
NCT-4M-B31AF Bullet Camera
Quick Start Guide
