Nuvation Energy NUV100-CI-12-1 Скачать руководство пользователя страница 96

Страница: 96 / 109

10.2.1. Wireshark (Windows/Linux)

1. Download/install Wireshark on a PC (

https://www.wireshark.org/

)

2. Connect the PC directly to the Ethernet port on the Stack Switchgear

3. Start a Wireshark capture on the network interface connected to the Stack Switchgear

4. In the 'filter' field, enter in

arp.isgratuitous

and press enter

5. Either reboot the Stack Switchgear, or unplug/plug the Ethernet cable

6. The device should send a 'Gratuitous ARP' on the Ethernet network. In Wireshark the 'Info' field

looks like:

Gratuitous ARP for <IP> (Request)

where the

<IP>

is the address for the Stack

Switchgear

7. Once that is complete, update the PC network settings to match the Stack Switchgear and

connect the Operator Interface.

•

Refer to

Section 5.2

for instructions.

10.2.2. Netdiscover (Linux only)

1. Install

netdiscover

on a PC (on Debian based systems use:

sudo apt install netdiscover

)

2. Connect the PC directly to the Ethernet port on the Stack Switchgear

3. Run

sudo netdiscover -i <interface> -p

where

is the network interface connected to the

Stack Switchgear

4. Either reboot the deStack Switchgearvice, or unplug/plug the Ethernet cable

5. The device address and MAC will show up in

netdiscover

once an ARP packet is sent

6. Once that is complete, update the PC network settings to match the Stack Switchgear and

connect the Operator Interface.

•

Refer to

Section 5.2

for instructions.



In the event the IP address cannot be discovered, contact

[email protected]

for assistance.

Nuvation Energy High-Voltage BMS - Product Manual

Document ID: NE-PM-003

Rev 1.2, 2021-03-03

Curie Update 1

Содержание NUV100-CI-12-1














































































































Результаты поиска

Содержание NUV100-CI-12-1

Отзывы:

Похожие инструкции для NUV100-CI-12-1

Бренды по названию

Популярные бренды

Nuvation Energy NUV100-CI-12-1, Руководство по эксплуатации продукта

Результаты поиска

Содержание NUV100-CI-12-1

Отзывы:

Похожие инструкции для NUV100-CI-12-1

Бренды по названию

Популярные бренды