NWS15Z
Smart Wall Switch
Your phone is smart. Your home should be too.
Thank you for purchasing a NuTone Smart Home Series product that will allow
you to automate your home on your terms. To control your lights from your favorite
Home Automation app you will need to replace an existing switch with a NuTone
Smart Home Series switch. Choose your favorite Home Automation gateway with
Z-Wave, connect it to the internet and start adding NuTone Smart Home Series
switches to control your lights!
COMPONENTS SUPPLIED
TOOLS REQUIRED
• Transmitter
• Screws, Transmitter Mounting
• Wall Plate
• Screws, Wall Plate mounting
• Screwdriver, Flat Head
• Screwdriver, Phillips Head
• Pliers
• Wire Connectors
DANGER! SHOCK HAZARD. Read and understand
the installation instructions and this quick start guide before
installing. This device is intended for installation in accordance with
the National Electric code and local regulations in the United
States, or the Canadian Electrical Code and local regulations in
Canada. It is recommended that a qualified electrician perform this
installation. Retain instructions and guide for future use.
IC NOTICE
This Class B digital apparatus complies with Canadian ICES-003. Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired
operation of the device.
Ensure your favorite home automation gateway (SOLD SEPARATELY) has
Z-Wave, connect it to the internet and you are now ready to add the
NWS15Z Smart 3-Way Wall Switch
Turn power
OFF for switch at
the main circuit breaker panel.
Multiple switch preparation.
Broan-NuTone LLC 926 West State Street Hartford, WI 53027
NuTone.com Toll Free (855) 249-0610
INSTALLATION
OPERATION
Remove wall plate from switch.
2
Install
NWS15Z
in wall box.
1
3
4
5
Remove screws and switch.
Disconnect all switch wires.
6
7
8
Connect all switch wires.
If NWS15Z will be installed into a box
with other switches, scored tabs on
the switch should be removed as
required. Do NOT remove outside
tabs on the ends of switch groups.
To remove, bend tab back and forth
with pliers until it snaps free of switch.
Refer to the NWS15Z instructions included with this Transmitter
Switch and the Home Automation gateway instructions for your
specific system to add devices to your system network.
When adding this device to the network, push the top or the
bottom of the switch when requested by the controller to
define its operation in the system.
Turning Z-Wave devices ON or OFF
When NWS15Z has been added to the network it operates
as follows:
•
Tap top of switch to turn ON
•
Tap bottom of switch to turn OFF.
The LED on the NWS15Z will indicate the status of the devices
you are controlling. The LED will flicker when it is transmitting
commands to any of the group networks. This can be changed.
See the “NWS15Z Instructions” included with the transmitter.
15
OFF
ON
Turn power
ON for switch at
the main circuit breaker panel.
9
10
15
OFF
ON
QUICK START GUIDE
Ensure power to all
wires in box is turned
OFF.
The NWS15Z Smart 3-Way Wall Switch has
Z-Wave certification which guarantees compatibility.
SPECIFICATIONS
Power: 120 VAC, 60 Hz
Signal: (Frequency) 908.42 MHz, 9.6Kbps or 40Kbps capable
Range: Up to 100 feet line of sight between the Controller and/or closest Z-Wave repeater.
1. Place your Home Automation gateway with Z-Wave into
Discovery or Add mode.
2. Push the top or bottom rocker of the switch when
requested by the controller to add it into your Home
Automation system.
3. Refer to your Z-Wave controllers instructions for additional
information on adding devices.
System Pairing adding the NWS15Z to your controller
Smart Wall Switch, 15Amp
99045339A
REGULATORY INFORMATION
The NWS15Z is certified to comply with applicable FCC and IC rules
and regulations governing RF and EMI emissions.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesired operation.
FCC NOTICE
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions may
cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
A video of this installation procedure can be viewed on-line at:
www.nutone.com/HomeAutomation
For additional help, please view the NWS15Z Troubleshooting
and FAQ guide.
Z-Wave® is a registered trademark of Sigma Designs
Install wall plate.
Convert standard White (included) to Almond with
Trim Kit sold separately.
3
4
POWER
(BLACK)
3
NEUTRAL
(WHITE)
2
GROUND
(GREEN)
4
LOAD
(BLACK)
1
1
2
3
4
POWER
(BLACK/BLACK)
3
NEUTRAL
(WHITE)
2
GROUND
(GREEN)
4
LOAD
(BLUE/BLACK)
1
1
2
