NWO15Z
Smart Wall Outlet
Your phone is smart. Your home should be too.
No one offers a safer Z-Wave smart outlet – tamper resistant preventing
children from inserting household objects into outlet. To control your small
appliances or lamps from your favorite Home Automation app you will need to
replace an existing outlet with a NuTone Smart Home Series Outlet. Choose
your favorite Home Automation gateway with Z-Wave, connect it to the internet
and start adding NuTone Smart Home Series Outlets to turn on your coffee pot
when you wake up, automatically turn off your curling iron in the morning, or
schedule anything plugged into the controlled outlet all from your Smart Phone.
COMPONENTS SUPPLIED
• Transmitter
• Screws, Transmitter Mounting
• Wall Plate
• Screws, Wall Plate mounting
DANGER! SHOCK HAZARD.
Read and understand
the installation instructions and this quick start guide before
installing. This device is intended for installation in accordance with
the National Electric code and local regulations in the United
States, or the Canadian Electrical Code and local regulations in
Canada. It is recommended that a qualified electrician perform this
installation. Retain instructions and guide for future use.
IC NOTICE
This Class B digital apparatus complies with Canadian ICES-003. Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired
operation of the device.
Ensure your favorite home automation gateway (SOLD SEPARATELY) has
Z-Wave, connect it to the internet and you are now ready to add the
NWO15Z Smart Wall Outlet
Turn power
OFF
for switch at
the main circuit breaker panel.
Broan-NuTone LLC 926 West State Street Hartford, WI 53027
NuTone.com Toll Free (855) 249-0610
INSTALLATION
OPERATION
Remove wall plate from outlet.
2
Install
NWO15Z
in wall box.
Install wall plate.
1
3
4
5
Remove screws and outlet.
Disconnect all outlet wires.
Connect all outlet wires using
wire connectors.
6
7
8
Refer to the NWO15Z instructions included with this Smart Wall
Outlet and the Home Automation gateway instructions for your
specific system to assign devices to your system network.
When adding this device to the network, push button once
when your controler indicates.
When your Home Automation gateway has been configured for
all devices connected to the network, the NWO15Z operate as
follows:
•
Push and release to turn power ON
•
Push and release to turn power OFF
•
Or control from your smart phone using your Home Automation app.
15
OFF
ON
Turn power
ON
for switch at
the main circuit breaker panel.
15
OFF
ON
9
QUICK START GUIDE
Ensure power to all
wires in box is turned
OFF.
The NWO15Z Smart Wall Outlet has
Z-Wave certification which guarantees compatibility.
SPECIFICATIONS
Power: 120 VAC, 60 Hz
Signal: (Frequency) 908.42 MHz
Range: Up to 100 feet line of sight between the Controller and/or closest Z-Wave repeater.
Smart Wall Outlet, 15Amp
1
2
1
2
3
Turning Z-Wave devices ON or OFF
ALWAYS POWERED OUTLET
CONTROLLED OUTLET
99045341A
1. Place your Home Automation gateway with Z-Wave into
Discovery or Add mode.
2. Follow the instructions in your Home Automation gateway
or app.
3. Refer to your Z-Wave controllers instructions for additional
information on adding devices.
System Pairing adding the NWO15Z to your controller
REGULATORY INFORMATION
The NWO15Z is certified to comply with applicable FCC and IC rules
and regulations governing RF and EMI emissions.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesired operation.
FCC NOTICE
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions may
cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
A video of this installation procedure can be viewed on-line at:
www.nutone.com/HomeAutomation
For additional help, please view the NWO15Z Troubleshooting and FAQ guide.
POWER
(BLACK)
1
NEUTRAL
(WHITE)
2
GROUND
(GREEN)
3
3
POWER
(BLACK)
1
NEUTRAL
(WHITE)
2
GROUND
(GREEN)
3
TOOLS REQUIRED
• Screwdriver, Flat Head
• Screwdriver, Phillips Head
• Pliers
• Wire Connectors
Z-Wave® is a registered trademark of Sigma Designs
