background image

 PRODUCT COMPONENTS

 TILT SENSOR INSTALLATION AND BATTERY

 PAIRING (INCLUDING) WITH THE SYSTEM

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,NGD00Z - P/N: 10006014 X5 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - TOL. +/-.125" - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 1 OF 2

 WARNING 

This operator system is equipped with an unattended 

operation feature. This door could move unexpectedly. 

NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR!

 WARNING 

This system can be installed on sectional type (roll up) doors 

only per (UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!

 WARNING 

Do not install the Remote Command Transceiver on 

garage door operators manufactured prior to 1993 

(models without an operational safety beam entrapment 

detection system).

 WARNING 

The Remote Command Transceiver must be mounted in 

the garage, in sight of the garage door, where the visual 

and audible movement warning indicators can be clearly 

seen and heard.

NGD00Z

POWER

INPUT

JACK

WARNING

LIGHT

LINK

BUTTON

CONNECTION

WIRES

MOUNTING SCREWS

AND ANCHORS

POWER

SUPPLY

TILT

SENSOR

STATUS

INDICATOR

OPTIONAL

ADJUSTABLE

MOUNTING

BRACKET

POWER

SUPPLY

RETAINING

BRACKET

SCREWS AND

MOUNTING TAPE

FOR TILT SENSOR

SCREW AND

MOUNTING HARDWARE

FOR ADJUSTABLE

BRACKET

SCREW FOR

POWER SUPPLY

BRACKET

WIRE

TIES

TO INCLUDE THE NGD00Z

INTO YOUR CONTROLLER

1

2

WALL

OUTLET

POWER

SUPPLY

POWER

INPUT

JACK

LINK

BUTTON

NGD00Z

Press and release the link button

on the NGD00Z.

Note: Plug in the NGD00Z
near your Z-Wave Controller

for these steps

Place your Z-Wave Controller into

Discovery or Include mode.

TO EXCLUDE THE NGD00Z

FROM YOUR CONTROLLER

Confirm that the NGD00Z was

recognized by your Z-Wave Controller.

Refer to your Z-Wave Controllers

instructions for additional information
on including devices.

3

1

2

Press and release the link button

on the NGD00Z.

Place your Z-Wave Controller into

Exclude mode.

Confirm that the NGD00Z was
excluded by your Z-Wave Controller.

Refer to your Z-Wave Controllers
instructions for additional information
on excluding devices.

3

CR2032

PLUS SIDE UP !!!

The system will notify you
when the battery is low,
replace the battery with
a type CR2032 coin cell

Insert the
battery
into the
transmitter

To open the case, twist
a small screwdriver
in case slot 

SLOT

 Use double sided tape or

the two mounting screws supplied

(drill 1/16" pilot holes if required)

POST ON

BOTTOM

"UP"

ARROWS

Snap the sensor onto
the mounting plate

To activate the tilt sensor,
remove the battery protection pull strip

2

ARROWS ON PLATE

& SENSOR POINT UP

LOW BATTERY REPLACEMENT

1

2

1

3

Attach the mounting plate
to the 

top panel of the door

NGD00Z Overview

•  A garage door opener remote 

command transceiver with built-in 

Z-Wave technology.

•  Allows remote operation of a garage 

door opener using Z-Wave controllers.

•  Acts as a Z-Wave repeater to improve 

communications within the Z-Wave 

mesh network.

NGD00Z Summary of Operation

•  NGD00Z connects to the garage door 

opener’s pushbutton wall console 

terminals.

•  A wireless tilt sensor mounts on the 

garage door and reports the door’s 

position to the NGD00Z.

•  NGD00Z responds to Z-Wave 

commands from Z-Wave controllers to 

open or close the garage door.

•  A warning indicator light flashes and 

a beeper sounds for 5 seconds before 

the door begins to move.

•  If the door does not completely 

open or close, a second open or 

close command can be sent after 

30 seconds.

•  If the door does not completely open 

or close after the second attempt, 

the NGD00Z operation is suspended 

until a local garage door pushbutton is 

activated.

Z-Wave Information

•  Z-Wave® is a registered trademark 

of Sigma Designs Inc. and/or its 

subsidiaries.

•  Z-Wave is an Interoperable two-way RF 

mesh networking technology designed 

for use with a Z-Wave gateway/

controller and other Z-Wave enabled 

devices.

•  Replication is the process of copying or 

transferring your Z-Wave network from 

one controller to another.

•  This is a Security enabled Z-Wave 

product and must be used with a 

Security enabled Z-Wave controller 

in order to fully utilize this product. As 

such, this device will not respond to 

Basic CC commands.

•  ASSOCIATION: The NGD00Z supports 

1 Group with 1 Node. Group 1 must be 

assigned the Node ID of the controller 

to which unsolicited notifications from 

the NGD00Z will be sent. The Z-Wave 

controller should set this association 

automatically after inclusion.

NGD00Z

GARAGE DOOR OPENER 
REMOTE COMMAND 
TRANSCEIVER 
with TILT SENSOR

Installation Instructions

 PRODUCT DESCRIPTION

 SAFETY NOTES

Отзывы: