Nu-Flame SYNERGY ELLESSE Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 34

Nu-Flame SYNERGY ELLESSE Скачать руководство пользователя страница 10

10

8.2 The Synergy Ellesse is available with various Trim Styles with Glass or Metal Door Options.
Some Styles also have a Sealing Frame Option (Normally used for Wall Mounted Installations).

The general dimensions are shown with a table below showing the minimum flat area required around the Fireplace Opening

The Synergy Ellesse Steel & Glass Options can be supplied with or without the Sealing Frame for different applications.
The Synergy Ellesse Steel can only be Installed below a Wall Mounted Television if Installed in a Suitable Fire Surround.
All other Trim Options can be Installed below a Wall Mounted Television be it in a suitable fire surround or wall mounted subject to
specific requirements which should be discussed with your Nu-Flame stockist and subject to the requirements in these Instructions.

  The Side Views show how far the Trims project from the wall.

Minimum Flat Sizes for Doors & Frames (Central Around Opening)

Width (mm)

Height (mm)

Synergy Ellesse Echo Trim with Metal Door

1140mm 540mm

Synergy Ellesse Echo Trim with Glass Door

1140mm 540mm

Synergy Ellesse Steel Trim (No Sealing Frame)

1135mm 560mm

Synergy Ellesse Steel Trim (With Sealing Frame)

970mm 630mm

Synergy Ellesse Glass Trim (No Sealing Frame or Shelf)

980mm 550mm

Synergy Ellesse Glass Trim (With Sealing Frame & Shelf)

980mm 605mm

Note:

Where a the Synergy Ellesse Steel or Glass Trims combinations is to be Installed in a Fire Surround a Riser Plate Must

have been specified which will raise the fire by 30mm to allow for the Metal or Glass Door to open clear of the Hearth.

Note:

Where a the Synergy Perspective Glass Trim is to be Wall Mounted the Glass Shelf will be supplied and

Must

always be

fitted.

Note:

This does not take account of any up stand that may be present around the Hearth for which a greater height allowance

may be required. More detail is provided in Section 15.

SYNERGY ELLESSE
WITH ECHO FRAME & GLASS DOOR

SYNERGY ELLESSE STEEL
(AVAILABLE WITH OR WITHOUT SEALING FRAME

SYNERGY ELLESSE
WITH ECHO FRAME & METAL DOOR

SYNERGY ELLESSE GLASS
(AVAILABLE WITH OR WITHOUT SEALING FRAME & GLASS SHELF

«
...
8
9
10
11
12
...
»

Содержание SYNERGY ELLESSE



































Отзывы:

Нет отзывов