nStor NexStor 4200F Series Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 174

background image

Chapter 3 - Setup and Installation

Duplex Mode (NexStor 4220F)

69

Duplex Mode (NexStor 4220F)

The basic duplex operating mode provides a single enclosure with dual RAID

Controllers. The two controllers operate in a dual-active configuration, where both

controllers are actively processing data. This greatly improves the overall system

performance and provides the most robust system redundancy. You can choose

either a Multi-Port or a Multiple Target ID (TID) topology when using the duplex

mode. This attribute is selected from the software.

In the Multi-Port operating mode, all host ports are active and connected to

individual Fibre loops. This mode requires alternate path software since it does

not support transparent failover and failback operations.

In the Multiple Target ID operating mode, the controller has the ability to

function as multiple target ports on a single arbitrated loop. During failover, the

surviving controller enables a virtual port, impersonating the ports from the failed

controller.

The duplex mode supports several cabling configurations for Multi-TID and

Multi-Port. The configurations demonstrate attachments to a single enclosure and

multiple enclosures.

NOTE:

Split-bus mode is not supported when a RAID Controller is installed.

CAUTION:

The bus speed must be set to the same setting between the disk
drives and the Disk I/O card(s), and then the host system HBAs
(BIOS setting) and the Host I/O cards. For example, if you are using
2 Gb drives, the Disk I/O cards must be set to 2 Gb mode. If your
host system HBA(s) is set to 1 Gb mode, the Host I/O card(s) must
be set to 1 Gb mode.

Multi-TID Single Host-Single Connection Configuration

1

Set the jumper (JP4) on the Disk I/O card to configure the bus speed mode.

Loosen the two captive fastener screws for the Disk I/O card and pull it from

the enclosure using the fastener screws. Locate the jumper JP4 and position it

for the desired speed setting, (installed on one pin only for 2 Gb mode and

on both pins for 1 Gb mode).

4200F.book Page 69 Thursday, January 23, 2003 2:47 PM

«
...
79
80
81
82
83
...
»

Содержание NexStor 4200F Series















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NexStor 4200F Series

Бренд: ECKELMANN Страницы: 134

d2 Ethernet Disk mini

Бренд: LaCie Страницы: 23

Бренд: Edirol Страницы: 1

HAWK 2 ST11900W

Бренд: Seagate Страницы: 40

Бренд: Seagate Страницы: 54

Бренд: DataWhale Страницы: 31

GHESS 9.8-14.4-TH

Бренд: GMDE Страницы: 50

Бренд: Yardmaster Страницы: 20

VPFEM4128GSCBMTL

Бренд: Viking Technology Страницы: 36

Hybrid Home 4,8

Бренд: Hybrid Страницы: 42

Бренд: OpenEye Страницы: 23

EonStor GS 3000 Series

Бренд: Infortrend Страницы: 134

Бренд: Western Digital Страницы: 2

Бренд: HOLZMANN MASCHINEN Страницы: 18

Бренд: morse Страницы: 6

Бренд: Sun Microsystems Страницы: 118

Бренд: Symantec Страницы: 2

Бренд: Western Digital Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды