manualshive.com logo in svg

nStor NexStor 4200F Series, Руководство пользователя

Поделиться
Скачать
nStor NexStor 4200F Series Скачать руководство пользователя страница 54

Chapter 3 - Setup and Installation

Storage System Detailed Installation

42

Storage System Detailed Installation

This section describes preparing and installing the NexStor 4200F Series Storage 
System enclosure(s) into the rack cabinet or the enclosure into its tower stand 
“Installing the Storage System into the Tower Stand” on page 45.

After installing the hardware components, go to the “Operating Mode 
Configuration and Cabling” section, and set the SES Controller card switches as 
described and cable the enclosure(s) for your selected topology.

Installing the Storage System Enclosure into the Rack Cabinet

1

Install the storage enclosure(s) into the rack cabinet.

Select an appropriate location within your rack cabinet. You should consider 
the location of the enclosure(s) in relationship to each other to ensure that 
the cables will easily reach between enclosures.

CAUTION:

The power supplies should be removed prior to installing the 
enclosure. The enclosure chassis could be damaged during 
installation process due to the added weight of the power supplies.

2

Remove each enclosure from its shipping carton and inspect for obvious 
damage. Place the enclosure on a flat surface to work from.

3

Remove the front bezel from the accessory box and store it in a location 
where it will not be damaged. It will be installed later in the installation 
procedures.

4

Remove the power supplies.

From the rear of the enclosure, remove a power supply by grasping its 
handle and pressing in on the release latch with your thumb as you pull the 
power supply from the enclosure. Repeat for the other power supply.

5

Locate the mounting hardware in the accessory kit (mounting rails, screws, 

and nuts – on some rack installations you will use cage nuts and on some 

racks they will be standard nuts).

NOTE:

It will be helpful to have an assistant available during the installation.

6

Lift and secure the enclosure into the rack cabinet.

a

Position the enclosure in the cabinet at the desired location.

4200F.book  Page 42  Thursday, January 23, 2003  2:47 PM

Содержание NexStor 4200F Series















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды