nStor NexStor 4200F Series Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 174

nStor NexStor 4200F Series Скачать руководство пользователя страница 33

21

Chapter 2

Topologies and Operating Modes

This chapter provides a functional overview of the supported operating modes
and topologies for the NexStor 4200F Series Storage System. Information
contained in this chapter should provide you with an understanding to make the
best choice to optimize your storage system solution.

Essentially there are two operating modes available: Simplex (Stand-Alone) and
Duplex (Active-Active). The NexStor 4210F model with its single RAID controller
supports the simplex operating mode, and the NexStor 4220F with its dual RAID
controllers supports the duplex or active-active operating mode.

Operating Mode Overview

These operating modes allow you to configure the enclosure’s drives and RAID

controller(s) to support a variety of host environments topologies.

■

Simplex – In this operating mode, the enclosure is configured as a RAID

storage system with its single RAID controller operating autonomously.

This mode supports a dual port topology.

■

Duplex – In this operating mode, the enclosure is configured as a RAID

storage system with dual controllers operating in an active-active

fault-tolerant configuration. This mode supports both Multi-TID and

Multi-Port topologies.

4200F.book Page 21 Thursday, January 23, 2003 2:47 PM

«
...
31
32
33
34
35
...
»

Содержание NexStor 4200F Series















































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды