manualshive.com logo in svg

nStor NexStor 4200F Series, Руководство пользователя

Поделиться
Скачать
nStor NexStor 4200F Series Скачать руководство пользователя страница 21

 

Chapter 1 - Getting Started

 

Spin-Up Settings

 

9

 

Spin-Up Settings

 

Switches 7 and 8 control the drive spin-up functions. The switches are directly 
attached to all of the drive slot start signals. Switch 7 controls the “Start_1” signal 
(Delay Spin-up) and switch 8 controls the “Start_2” signal (Remote Spin-up).

The table below describes the functional mode for each switch.

 

Disk I/O Card

 

The Disk I/O card provides drive channel expansion to the daisy chain NexStor 
4000F enclosures. This card has circuitry which act as an active hub and provides 
automatic loop regeneration (LRC) and port bypass. This loop regeneration will 
“heal” the FC-AL (Fibre Channel-Arbitrated Loop) when components become 
disconnected or faulty. 

There are two Disk I/O cards installed at the rear of the enclosure adjacent to the 

cooling fan bay. The upper Disk I/O card connects to the “Loop A” side of the 

disk drives, and the lower Disk I/O card provides the connection to the “Loop B” 

side of the disk drives.

Each Disk I/O card supports Small Form-Factor Pluggable (SFP) cages to accept 

either optical or copper transceivers. They are designed to support NCITS T11 

Fibre Channel compliant devices at speeds of 1.0625 Gb per sec or 2.125 Gb per 

second. The speed is set through a hardware jumper (JP4) located on the Disk 

I/O card. Setting the jumper on both pins will enable the 1 Gb/sec mode, 

likewise offsetting the jumper will enable the 2 Gb/sec mode. An LED on the 

card will illuminate to indicate the 2 Gb mode.

 

“DL” Switch 7

“RM” Switch 8

Drive Spin-up Mode

 

Down (0)*

Down (0)*

Drive motor spins up at DC power on.

Down (0)

Up (1)

Drive motor spins up only on SCSI “start” 
commands.

Up (1)

Down (0)

Drive motor spins up after a delay of 12 
(may vary depending on drive type) seconds 
times the numeric ID setting of the 
associated drive.

Up (1)

Up (1)

Drive motor will not spin-up.

 

*  Default setting for proper operation.

 

4200F.book  Page 9  Thursday, January 23, 2003  2:47 PM

Содержание NexStor 4200F Series















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды