nStor NexStor 4200F Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 174

nStor NexStor 4200F Series Скачать руководство пользователя страница 17

Chapter 1 - Getting Started

Cooling Fan Module

5

Cooling Fan Module

The cooling system consists of two high-performance (80-CFM) cooling fans
mounted in a single fan module which slides into the open bay at the rear of the
enclosure. The design of the fan module provides for an easy user-replaceable
component in a live environment without interruption of service.

If any one fan should fail, cooling redundancy and efficiency are degraded. The
SES processor communicates monitoring status of the cooling fans which will
illuminate the Fan Status LED and sound an alarm should a problem occur.

The enclosure temperature sensors monitor the enclosure temperature for
out-of-tolerance conditions. The maximum temperature threshold value is 60° C
(140° F). If the threshold value is exceeded, the Fan Status LED will begin flashing
amber. This LED notification gives the user a warning that some condition is
causing the enclosure temperature to exceed its limits and action is required by the
user to determine the cause and take corrective action. It may be due to a blockage
of air flow or a low fan speed.

WARNING:

Do not operate the enclosure for extended periods of time (greater
than 5 minutes) with the cooling fan module removed.

The firmware-based VT-100 interface has an option to manage fan speed. This option
provides a whisper mode fan operation for noise sensitive environments. When
enabled (default) and based on a set of conditions, the firmware will manage the
cooling fans speed to maintain the enclosure temperature while minimizing noise
levels. Refer to “Enclosure Fan Speed Control” on page 113 for more details on using
this option.

Cooling Fan Module

Jumpers JP1 and JP2
Fan Speed Overr ide Control

4200F.book Page 5 Thursday, January 23, 2003 2:47 PM

«
...
15
16
17
18
19
...
»

Содержание NexStor 4200F Series















































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды