nStor NexStor 4200F Series Скачать руководство пользователя страница 119

Страница: 119 / 174

Chapter 4 - Managing and Monitoring

LED Matrix

107

LED Matrix

The RAID Controllers have control of the Drive Status and Drive Activity LEDs.

Front Bezel LEDs

These LEDs which are located on the front bezel present the information in the

form of different colors and states (steady and flashing), as well as corresponding

audible alarms. Refer to the table below for a description of the LED conditions and

their meaning:

Front Bezel LED & Audible Alarm Matrix

Condition

Drive Status LED

Channel Status LED

Audible Alarm

Power Up

Steady Green for
inserted drives.

Blinking Green until
the controllers are
ready.

Short Beep.

Simplex Mode Controller Soft
Boot/Reset

Steady Green for
inserted drives.

Blinking Green until
the controllers are
ready.

Short Beep.

Duplex Mode Single Controller
Reset

Steady Green for
inserted drives.

Steady Amber until
the controllers are
ready.

Continuous Beep.

RESET ALARM

Drive LEDs

Alarm Reset Button

(One-Touch Annunciation)

Power On LED

Channel Status LED

Power Supply Status LED

Cooling Fan Status LED

Status LEDs

Activity LEDs

Status LEDs

Activity LEDs

Status LEDs

Activity LEDs

Status LEDs

Activity LEDs

Drive Slot 1

Drive Slot 4

Drive Slot 7

Drive Slot 10

Drive Slot 2

Drive Slot 5

Drive Slot 8

Drive Slot 11

Drive Slot 3

Drive Slot 6

Drive Slot 9

Drive Slot 12

4200F.book Page 107 Thursday, January 23, 2003 2:47 PM

Содержание NexStor 4200F Series















































































































































































Результаты поиска

Содержание NexStor 4200F Series

Отзывы:

Похожие инструкции для NexStor 4200F Series

Бренды по названию

Популярные бренды

nStor NexStor 4200F Series, Руководство пользователя

Результаты поиска

Содержание NexStor 4200F Series

Отзывы:

Похожие инструкции для NexStor 4200F Series

Бренды по названию

Популярные бренды