nStor NexStor 4200F Series Скачать руководство пользователя страница 115

Страница: 115 / 174

103

Chapter 4

Managing and Monitoring

In this chapter you will find information for using the enclosure’s onboard

monitoring systems. Also you will find procedures to update the enclosure’s SES

Controller card firmware.

Using a VT-100 terminal (or emulation), the SES RS-232 Service port provides an

interface to the enclosure’s monitoring system and firmware.

You should monitor your storage system regularly to ensure that the disk drives,

controllers, arrays, and enclosure components are working properly. The front

bezel LEDs provide monitoring information on enclosure components, fan status,

disk drive status, controller status, and array monitoring. The “One-Touch

Annunciation” Configuration Display provides information about switch settings,

Host and Disk I/O card presence, and controller presence from the touch of the

reset button.

Enclosure Component Monitoring

This section covers notifications provided by the front bezel LEDs and a detailed

explanation of the “One-Touch Annunciation” Configuration Display system.

As part of the monitoring notifications, an audible alarm works in conjunction

with the enclosure’s front bezel LEDs, and will sound an alert for any fault that

occurs with an enclosure component, logical array, or disk drive. To silence the

alarm, simply press the Alarm Reset button.

4200F.book Page 103 Thursday, January 23, 2003 2:47 PM

Содержание NexStor 4200F Series















































































































































































Результаты поиска

Содержание NexStor 4200F Series

Отзывы:

Похожие инструкции для NexStor 4200F Series

Бренды по названию

Популярные бренды

nStor NexStor 4200F Series, Руководство пользователя

Результаты поиска

Содержание NexStor 4200F Series

Отзывы:

Похожие инструкции для NexStor 4200F Series

Бренды по названию

Популярные бренды