manualshive.com logo in svg

NSK Surgic Pro2, Руководство по эксплуатации, Страница: 43 / 55

Поделиться
Скачать
NSK Surgic Pro2 Скачать руководство пользователя страница 43

42

Troubleshooting

Problem

Cause of Problem

Action

After the power is 
ON, “CONNECT” or 
“PUSH FC” is 
displayed and the 
screen is not 
switched�

Foot control is not connected�

Keep pressing the speed control pedal of the foot control while 
“PUSH FC” is displayed on the LCD display� If the screen does not 
change after 5 minutes, press and hold the Cancel key� The 
normal screen is displayed�
See “4 – 2 Installing foot control batteries” and replace the foot 
control batteries to check if it can be connected�
If it cannot be connected after replacing the batteries, see 
“8 – 1 – 1 Pairing with foot control” for pairing�
If this does not resolve the issue, please contact an authorized 
NSK dealer�

Will not rotate even 
if the foot control is 
pressed�

Foot control is not connected�

Perform the following after confirming that nothing is blocking the 
signal between the foot control and control unit�
•  Turn the main unit power off and on again to connect to the 

control unit�

•  See “4 – 2 Installing foot control batteries” and replace the foot 

control batteries with new ones�

•  See “8 – 1 – 1 Pairing with foot control” and perform pairing�
If this does not resolve the issue, please contact an authorized 
NSK dealer�

Foot control pedal and button 
response is poor due to not 
being used for a long period of 
time�

See “7 – 3 Foot control calibration” and calibrate the foot control� 

Malfunction of control unit or 
foot control

If the problem is not solved by checking foot control batteries or 
foot control connection status, system repair is required�

“COM ERR FC” is 
displayed�

Foot control not connected

Press the Cancel key to cancel the error� After confirming that  
nothing is blocking the signal between the control unit and the 
foot control, wait for a while to check if the foot control is 
connected automatically� If it is not connected automatically, 
perform the following procedures�
•  Turn the control unit power off and on again to connect to the 

foot control�

•  See “4 – 2 Installing foot control batteries” and replace the foot 

control batteries with new ones�

•  See “8 – 1 – 1 Pairing with foot control” and perform pairing�
If this does not resolve the issue, please contact an authorized 
NSK dealer�

“COM ERR LK” is
displayed�

Link Module not connected

Press the Cancel key to cancel the error� After confirming that 
nothing is blocking the signal between the control unit and the 
Link Module, wait for a while to check if the Link Module is 
connected automatically� If it is not connected automatically, 
perform the following procedures�
•  Turn off and on both Surgic Pro2 and VarioSurg 3 connected to 

Surgic Pro2�

• See the Link Module manual and try the pairing again�
If this does not resolve the issue, please contact an authorized 
NSK dealer�

Содержание Surgic Pro2
























































Отзывы:

Нет отзывов