manualshive.com logo in svg

NSK Surgic Pro2, Руководство по эксплуатации

NSK Surgic Pro2 - инновационный хирургический аппарат с высокой точностью и надежностью. Бесплатное скачивание руководства по эксплуатации доступно на manualshive.com, чтобы пользователи могли ознакомиться с операционным руководством. Надежное и удобное оборудование для профессиональных медицинских процедур.

Поделиться
Скачать
background image

24

Operation Procedure

5 – 5 – 2  Link Module

The link function enables two systems (NSK VarioSurg 3 and Surgic Pro2) to be controlled by one foot control�
Connecting Link Module to the VarioSurg 3 enables the function to link with this device to be used�
See Link Module manual for the method of use�

1 

Turn on the VarioSurg 3�

2 

Press and hold the button on Link Module�

3 

When the LED turns blue, release the button�

4 

Pairing is successful when Surgic Pro2 beeps and 
displays “OK”�
Make sure   icon below is displayed and the device 
is connected� Also the LED of the Link Module turns 
green�

5 

Press 

 twice to end setting mode�

 CAUTION

 

●

If any abnormalities are found with VarioSurg 3 and Link Module, refer to the respective operation manuals�

 

●

If the button is not released after the LED turns blue, the LED blinks white and pairing stops� To pair, release the 
button, and after the LED lights white, proceed from step 2�

NOTICE

 

●

Connect the Link Module to the VarioSurg 3 beforehand�

Содержание Surgic Pro2
























































Отзывы:

Нет отзывов

Похожие инструкции для Surgic Pro2

Taylor Made 12008 Instructions preview
12008
Бренд: Taylor Made Страницы: 2
York Fitness 1003 Assembly Instruction Manual preview
1003
Бренд: York Fitness Страницы: 18
Safco 1005 Instructions preview
1005
Бренд: Safco Страницы: 2
Omni 4000 Series Operation & Maintenance Manual preview
4000 Series
Бренд: Omni Страницы: 193
Nektar Aura Setup And User Manual preview
Aura
Бренд: Nektar Страницы: 3
Youkey Q7 Instructions For Use Manual preview
Q7
Бренд: Youkey Страницы: 86
Wacker Neuson AR Operator'S Manual preview
AR
Бренд: Wacker Neuson Страницы: 62
Nautilus 9NP-B7524 Series Owner'S Instructions preview
9NP-B7524 Series
Бренд: Nautilus Страницы: 2
Nautilus Be strong NS 700X Owner'S Manual preview
Be strong NS 700X
Бренд: Nautilus Страницы: 34
Nautilus BE STRONG E916 Quick Start Manual preview
BE STRONG E916
Бренд: Nautilus Страницы: 21
Qlight SK Quick Start Manual preview
SK
Бренд: Qlight Страницы: 4
Radial Engineering StageBug SB-2 Quick Start Manual preview
StageBug SB-2
Бренд: Radial Engineering Страницы: 2
Radial Engineering Dragster Quick Start preview
Dragster
Бренд: Radial Engineering Страницы: 2
Turner Designs TD-700 Operating Manual preview
TD-700
Бренд: Turner Designs Страницы: 55
Walimex Pro LED Niova 150-F Pro 150W Bi Color Manual preview
LED Niova 150-F Pro 150W Bi Color
Бренд: Walimex Pro Страницы: 56
Sport-thieme 1698321 Information For Use preview
1698321
Бренд: Sport-thieme Страницы: 20
Qtx Derby9 Manual preview
Derby9
Бренд: Qtx Страницы: 6
Hussmann KH14 Installation Manual preview
KH14
Бренд: Hussmann Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды