NR Electric PCS-9785 Скачать руководство пользователя страница 33

Страница: 33 / 108

5 Hardware

PCS-9785 Satellite-Synchronized Clock

5-1

Date: 2014-10-15

5.1 Overview

This device consists several different modules. The application and terminal description of each
module will be introduced in this chapter.



MON module

provides management functions like communication with SAS, event record,

setting management etc.



CLK module

provides satellite signal receiver (BDS or GPS) and IRIG-B signal input

channel.



COM module

provides different output interfaces with other IEDs.



PWR module

converts the power supply into various voltage levels for different modules and

components in this device.



HMI module

is comprised of LCD, keypad, LED indicators and a multiplex RJ45 debugging

port.

5.2 Module Configuration (for EXAMPLE only)

This section shows several examples of device terminal view and module arrangement.

NOTICE!

The following figures should

NOT

be used as reference for device configuration or

wiring design. For such purpose, please use the latest corresponding Manufacture
Ordering Table and consult our design department.

NR1110

NR1145

NR1205

NR1218

NR1219

NR1216

NR1217

NR1220

IRIG-B 2

IRIG-B 1

GPS 2

GPS 1

NR1301

BO _CO M1

O PTO+

PWR +

PWR -

G ND

5V O K ALM

BO _ALM

BO _FAIL

BO _CO M2

BO _FAIL

O PTO-

BO _ALM

BO _FAIL

NR1301

BO _CO M1

O PTO+

PWR +

PWR -

G ND

5V O K ALM

BO _ALM

BO _FAIL

BO _CO M2

BO _FAIL

O PTO-

BO _ALM

BO _FAIL

Figure 5.2-1 Terminal view example

08020

Содержание PCS-9785













































































































Результаты поиска

Содержание PCS-9785

Отзывы:

NR Electric PCS-9785, Инструкция по эксплуатации, Страница: 33 / 108

Результаты поиска

Содержание PCS-9785

Отзывы: