25ct WiFi RGB String Lights
Models: SLWA-C9-25, SLWA-ICL-25
Thank you for purchasing our Novolink WiFi RGB String Lights!
To insure proper installation and prior to use, please read these instructions and all warnings thoroughly.
Scan the QR Code with your
WiFi-enabled Smartphone or
Tablet to go to the site.
WARNINGS: PLEASE READ BEFORE PROCEEDING
This string light set is not a toy - please keep it out of reach of children. The light set should not be plugged
in while still in the packaging. For indoor and outdoor use. Do not attempt to hard-wire the light set to another
light set. The electric cord cannot be replaced. Only use the included hardware/adapter. Caution: If the light
string is damaged or does not work properly, the whole unit should be replaced if under warranty, or disposed
of in accordance with local, state and federal regulations.
WARNING - RISK OF ELECTRIC SHOCK.
IF BULBS ARE BROKEN OR MISSING, DO NOT USE.
1. The total connected sets may not exceed the maximum allowed number of 2 extensions to an original set.
If this limit is exceeded, it may result in a risk of electric shock or malfunction.
2. Ensure that the supply cord and inner wiring are not subject to mechanical load/stress.
3. Never hang or mount any object to the lighting chain.
4. Always disconnect the supply cord from the electrical outlet when the light set is not in use, or when the area
where it is in use is unattended for long periods of time.
5. For outdoor use, ensure the electrical outlet or any extension cord is in compliance with the protection
class IP44 (splash-water proof). If there is any doubt, consult a professional electrician.
6. Each section of a connected light set must be mounted individually.
7. Dispose of an entire light set if any portion of it is mechanically or electrically damaged.
For videos, easy-installation tips and troubleshooting, visit:
https://www.novolinkinc.com/wifi-rgb-lights-setup
www.novolinkinc.com
Contains FCC ID: 2APYD-SLWAG40ICLC9
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
FCC WARNING
SCAN
1. Before use and mounting, place the light set on a clean, flat surface and check for any damage to the LED bulbs, connections, controller and bulb string.
2. Never use sharp or pointed objects to install or mount a string light set or chain.
3. Fixing with metal, braided wire, or similar devices is not advisable. Metal or braided wire can damage the insulation layers of the light set.
4. Suitable installation devices include cable conduits or soft cable ties. When using cable ties, ensure they are not excessively tightened to the
string to avoid damage to the insulation layers of the light set.
5. The supply cord and string light body must not be subject to push, pull or torsion forces.
6. Ensure a correct and secure connection between the AC plug, controller and bulb string. The end cap of the bulb string set must always be in
place and tightened.
7. Ensure that the AC plug and light string are not located in or near running water or drains (e.g. snow, streams, rain gutters).
8. If the light set does not work, have it checked by a certified technician.
TIPS BEFORE YOU BEGIN...
