Novexx ALX 924 Скачать руководство пользователя

Страница: 31 / 91

User Manual

ALX 92x

09/2016 | 02

Product description

Label sensor adjustments

Mechanical via thumb wheel with position indicator, electronical setting via display function

Material unwind

Dancer arm for smooth unwinding of labelling material, label reel unwind with integrated friction
brake

Material rewind

Stepper-motor driven rewind mandrel

Ambient conditions

Installation location

• Inside buildings
• Protected from wind and spray water
• Dry
• Not in areas with potentially explosive atmosphere

Operating temperature

• ALX 924/925: +5 bis +35°C
• ALX 926: +5 bis +30°C

Storage temperature

-20 to 70°C

Air humidity

45 to 75% (non-condensing)

Protection class

IP 21

Noise emissions

< 70dB(A)

Sea level

Operation to max. 2000 m above sea level

Interfaces

Interface

Details

RS-232

Baud rate: 1200-115200, 8 bits; suitable connection cable: 1:1 Sub-
D9 extension cable (plug/socket)

RS-232/422/485

Optional (I/O board

): Sub-D15, baud rate: 1200-115200, 8 bits

Ethernet

10/100 Base T with TCP/IP, LPD, RawIP printing, DHCP, HTTPD,
FTPD, SNMP

USB (V1.1)

2x USB-A host port, 1x USB-B device port, transfer rate 12 Mb/s.

Signal Interface USI

Optional (USI board

): General control signals, signal voltage: 24 V

[Tab. 13] Data interfaces on the ALX 92x.

Содержание ALX 924




























































































Результаты поиска

Содержание ALX 924

Отзывы:

Похожие инструкции для ALX 924

Бренды по названию

Популярные бренды

Novexx ALX 924, Руководство пользователя

Результаты поиска

Содержание ALX 924

Отзывы:

Похожие инструкции для ALX 924

Бренды по названию

Популярные бренды