Configuring Business Continuity Clustering Software
6
67
no
vd
ocx
(e
n)
13
Ma
y 20
09
6
Configuring Business Continuity
Clustering Software
After you have installed and configured Identity Manager and the Novell
®
Business Continuity
Clustering software, and you have configured file system mirroring, you need to set up the BCC
software.
Section 6.1, “Configuring Identity Manager Drivers for the Business Continuity Cluster,” on
page 67
Section 6.2, “Configuring Clusters for Business Continuity,” on page 73
Section 6.3, “BCC-Enabling Cluster Resources,” on page 78
6.1 Configuring Identity Manager Drivers for the
Business Continuity Cluster
The Identity Manager preconfigured templates for iManager that were installed when you ran the
Novell Business Continuity Clustering installation must be configured so you can properly manage
your business continuity cluster. The preconfigured templates include the following:
Cluster Resource Synchronization:
A set of policies, filters, and objects that synchronize
cluster resource information between any two of the peer clusters. This template must always
be configured, even in a single-tree business continuity cluster.
User Object Synchronization:
A set of policies, filters, and objects that synchronize User
objects between any any two trees (or partitions) that contain the clusters in the business
continuity cluster. Typically, this template is used to configure drivers when the clusters in your
business continuity cluster are in different eDirectory
TM
trees. You might also need to set up
User Object Synchronization drivers between clusters if you put User objects in a different
eDirectory partition than is used for the Cluster objects; however, this is not a recommended
configuration. See
Appendix B, “Implementing a Multiple-Tree BCC,” on page 127
for more
information about implementing BCC between two trees.
The Identity Manager engine and eDirectory driver must be installed on one node in each cluster.
The node where Identity Manager is installed must have an eDirectory full replica with at least read/
write access to all eDirectory objects that will be synchronized between clusters. For information
about the full replica requirements, see
Section 4.1.5, “Novell eDirectory 8.8,” on page 40
.
Identity Manager requires a credential that allows you to use drivers beyond an evaluation period.
The credential can be found in the BCC license. In the Identity Manager interface in iManager, enter
the credential for each driver that you create for BCC. You must also enter the credential for the
matching driver that is installed in a peer cluster. You can enter the credential, or put the credential in
a file that you point to.
Section 6.1.1, “Configuring the Identity Manager Drivers and Templates,” on page 68
Section 6.1.2, “Creating SSL Certificates,” on page 70
Section 6.1.3, “Synchronizing Identity Manager Drivers,” on page 70
Section 6.1.4, “Preventing Identity Manager Synchronization Loops,” on page 71
Содержание BUSINESS CONTINUITY CLUSTERING 1.1 SP2 - ADMINISTRATION
