manualshive.com logo in svg

Novatel SMART7, Инструкция по установке и эксплуатации

Поделиться
Скачать
Novatel SMART7 Скачать руководство пользователя страница 60

Chapter 4   SMART7 with SPAN Operation

SMART7 Installation and Operation User Manual v6

60

4.2.2 The IMU Body Frame

The definition of the IMU Body frame is given by the physical axes of the IMU and represents how the sensors
are mounted inside the IMU. Refer to

SMART7 Mechanical Specifications

on page 136 for illustrations of the

IMU Body frame axes.

The origin of this frame is not the enclosure center, but the center of navigation (sensor center).

4.2.3 The Vehicle Frame

The definition of the vehicle frame is as follows:

l

z-axis – points up through the roof of the vehicle perpendicular to the ground

l

y-axis – points out the front of the vehicle in the direction of travel

l

x-axis – completes the right-handed system (out the right-hand side of the vehicle when facing forward)

Figure 18: Vehicle Frame

4.2.4 The User Output Frame

The user output frame is an arbitrary frame, which can be optionally defined to transfer inertial output to a more
useful position or reference frame.

By default, SPAN position and velocity output is given at the center of navigation of the IMU. To output position
and velocity at a different location, specify a user offset translation using the

SETINSTRANSLATION

com-

mand.

By default, SPAN attitude output is the rotation from the Local-Level frame to the Vehicle frame. If attitude output
is desired relative to another frame, specify a user offset rotation using the

SETINSROTATION

command.

Содержание SMART7



















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды