Novanta IMS Liberty MDrive Ethernet TCP/IP Скачать руководство пользователя страница 6

Страница: 6 / 88

IMS-MN-LMDE42C_A

Intended Use

Liberty MDrive Ethernet TCP/IP

Intended Use

The product may only be used in compliance with all applicable safety regulations and

directives, the specified requirements, and the technical data.

Prior to using the product, perform a risk assessment in view of the planned application. Based

on the results, the appropriate safety measures must be implemented.

Since the product is used as a component in an entire system, ensure the safety of persons by

means of the design of this entire system (e.g., machine design).

Operate the product only with the specified cables and accessories. Use only genuine

accessories and spare parts.

DANGER

POTENTIAL FOR EXPLOSION

Install and use this equipment in non-hazardous locations only.

Failure to follow these instructions will result in death or serious injury.

Any use other than the use explicitly permitted is prohibited and can result in hazards.

Electrical equipment should be installed, operated, serviced, and maintained only by qualified

personnel.

Product Related

DANGER

HAZARD OF ELECTRICAL SHOCK, EXPLOSION, OR ARC FLASH

Remove all power from all devices before connecting or disconnecting inputs or outputs to any

terminal or installing or removing any hardware.

Failure to follow these instructions will result in death or serious injury.

When the system is started, the drives are usually out of the operator’s view and cannot be

visually monitored.

DANGER

EQUIPMENT OPERATION

Only start the system if there are no persons in the zone of operation.

Failure to follow these instructions will result in death or serious injury.

Drives may perform unintended movements because of incorrect wiring, incorrect parameter

settings, incorrect data, user programming bugs, or other errors. Further, interference (e.g.,

electromagnetic interference (EMI)) may cause unpredictable responses in the system.

WARNING

UNINTENDED MOVEMENT

• Carefully install the wiring in accordance with the electromagnetic compatibility (EMC)

requirements.

• Do not operate the drive system with unknown parameter settings or data.

Failure to follow these instructions can result in death, serious injury, or equipment damage.

The designer of any control scheme must consider the potential failure modes of control paths

and, for certain critical functions, provide a means to achieve a safe state during and after a

path failure. Examples of critical control functions are emergency stop, overtravel stop, power

outage, and restart.

Содержание IMS Liberty MDrive Ethernet TCP/IP

























































































Результаты поиска

Содержание IMS Liberty MDrive Ethernet TCP/IP

Отзывы:

Похожие инструкции для IMS Liberty MDrive Ethernet TCP/IP

Бренды по названию

Популярные бренды

Novanta IMS Liberty MDrive Ethernet TCP/IP, Руководство по оборудованию

Результаты поиска

Содержание IMS Liberty MDrive Ethernet TCP/IP

Отзывы:

Похожие инструкции для IMS Liberty MDrive Ethernet TCP/IP

Бренды по названию

Популярные бренды