Novanta i401 Скачать руководство пользователя страница 91

Страница: 91 / 133

FIRMWARE UPGRADE PROCEDURE

PAGE

Connect to the i401 laser

Remove DC power from the laser.

Locate the Ethernet crossover cable in the ship kit and connect it between your computer

and the i401’s Ethernet port.

Remove the Quick Start Plug from the i401’s User I/O connector.

Apply 48 VDC power to the laser and wait 15 seconds for the firmware to initialize.

If you have changed the i401’s IP address (the factory default is 192.168.50.50), you must

change it back. If not, proceed to the next section, Perform the firmware upgrade.

Launch your web browser, type the laser’s IP address, and then press Enter.

When the home page appears as shown in Figure below, click the Configure IP

Address link at the bottom of the page.

Figure 4-25 Configure IP Address link on I401 home page

When the Change IP Address page loads showing the default IP address (following

figure),

click the Submit button. This resets the laser’s IP address to 192.168.50.50.

Figure 4-26 i401 Change IP Address page

Содержание i401






































































































































Результаты поиска

Содержание i401

Отзывы:

Похожие инструкции для i401

Бренды по названию

Популярные бренды

Novanta i401, Руководство пользователя

Результаты поиска

Содержание i401

Отзывы:

Похожие инструкции для i401

Бренды по названию

Популярные бренды