Novanta i401 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 133

background image

INTRODUCTION

PAGE

|

9

Introduction

This section outlines the following information:

•

Trademark, Copywrite & Warranty information

•

Guidelines and contents description

•

i401 Nomenclature

Important Note: This Operation Manual explains operation activities related to i401 lasers. If you

cannot operate the unit using the information described in this manual, contact Novanta®

(+1.425.349.3500) or an authorized Novanta Distributor.
Do not lift or support the laser by its cooling fittings.
Failure to properly package the laser using Novanta shipping box and foam/cardboard inserts as shown

in Packaging Instructions may void the warranty. Customers may incur additional repair charges due to

shipping damage caused by improper packaging.
Before beginning any maintenance or inspections of your i401 laser, be sure to completely disable the

laser by disconnecting the DC Power cable (or cables) from the rear of the laser.

Trademark, Warranty & Copywrite

Novanta and I401 are registered trademarks of Novanta, Inc.
All other trademarks or registered trademarks are the property of their respective owners.
© 2013 by Novanta, Inc. All rights reserved.

Warranty Information

This is to certify that ® i401 lasers are guaranteed by Novanta, Inc. to be free of all defects in materials

and workmanship for a period of one year from the date of purchase. This warranty does not apply to

any defect caused by negligence, misuse (including environmental factors), accident, alteration, or

Caution: Possible Equipment Damage

Novanta does not recommend vertical or head down configurations.

Please contact the factory for limitations as a vertical orientation increases the risk of damage to the
laser’s optics.

A risk of exposure to toxic elements may result when certain optical or beam delivery components
are damaged. In the event of damage to laser, marking head, or beam delivery optics, contact
Novanta®, or the optics manufacturer for handling instructions.

If you operate your laser dirty or dusty environments, contact Novanta about the risks of doing so
and precautions you can take to increase the longevity of your laser, marking head, and associated

«
...
7
8
9
10
11
...
»

Содержание i401






































































































































Отзывы:

Нет отзывов

Похожие инструкции для i401

Бренд: Larson Davis Страницы: 193

Бренд: Facom Страницы: 116

Бренд: Omega Engineering Страницы: 22

Бренд: Xylem Страницы: 19

WALLACE & TIERNAN P7 ADVANCED

Бренд: Evoqua Страницы: 98

Бренд: Hilti Страницы: 146

Бренд: NARDA Страницы: 240

Proline Promag 50H

Бренд: Endress+Hauser Страницы: 52

Бренд: ScienTECH Страницы: 44

Бренд: Westfalia Страницы: 2

Бренд: AccuLine Страницы: 15

Бренд: T&D Страницы: 14

Бренд: Patlite Страницы: 21

Бренд: B&B Страницы: 37

Бренд: Haltech Страницы: 20

Бренд: Kawai Страницы: 24

Бренд: Apera Instruments Страницы: 20

Бренд: Elcometer Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды