Novanta f201 Скачать руководство пользователя

Страница: 92 / 105

OTHER LASER FAULTS

PAGE

RF Drive Switch fault

An RF Drive DC fault occurs on power-up when the tube fails to breakdown, or a fault occurs in the RF

Driver’s 96-volt switching circuitry. In this case, the Ready LED flashes 3 blinks. If an RF Drive DC fault

occurs, reset the laser by removing DC power to the laser, wait 30 seconds, and then reapply power. On

Keyswitch-equipped lasers, you must also toggle the Keyswitch from OFF/RESET to ON (or apply a ±5–

24 VDC Remote Reset/Start Request pulse with the Keyswitch set to ON) When the Ready LED illumi-

nates, lasing is enabled after a five-second delay. If the RF Drive DC fault reappears, contact NOVANTA

or a NOVANTA Authorized Distributor.

PWM Drive/RF Oscillation faults

New circuitry on the f201 RF board has eliminated PWM Drive and RF Oscillation faults. The 4-blink fault

indication no longer exists.

VSWR fault

A VSWR fault indicates an impedance mismatch between the tube and RF Driver and occurs when a PWM

Command signal is first applied. This fault is annunciated by the Shutter LED flashing continuously until

the fault disappears. If a VSWR fault occurs, the VSWR circuit limits the maximum PWM pulse length to 12

microseconds (

s). This equates to a 6% maximum duty cycle at a 5 kHz frequency or a 24% maximum

duty cycle at a 20 kHz PWM frequency. When the VSWR fault clears, the laser resumes normal operation

without cycling DC power. If the VSWR fault fails to clear or reappears, contact NOVANTA or a NOVANTA

Authorized Distributor.
The leading causes of VSWR failures are environmental conditions, like cold overnight temperatures while

the laser is off. In cases like this, it may take as long as 60 seconds for tickle to breakdown the tube and

begin normal daily operation.

Other laser faults

Each Symptom listed below describes a particular fault condition. For each Symptom, specific causes

and solutions are described in the Possible Causes section.

Symptom:

•

A remote interlock condition is indicated by the following status LEDs and I/O states:

Remote Interlock LED – Red   Interlock Open output – Closed
Temp LED – Green         Over Temperature output – Open
Ready LED – Off         Laser Ready output – Open
Lase LED – Off        Laser Active output – Open

Possible Causes:

Содержание f201










































































































Результаты поиска

Содержание f201

Отзывы:

Похожие инструкции для f201

Бренды по названию

Популярные бренды

Novanta f201, Руководство пользователя

Результаты поиска

Содержание f201

Отзывы:

Похожие инструкции для f201

Бренды по названию

Популярные бренды