Novanta f201 страница 91 Скачать руководство пользователя

Страница: 91 / 105

TROUBLESHOOTING

PAGE

Troubleshooting

On OEM lasers, remote interlock conditions are not latched. Re-establish the Remote Interlock signal input

(Remote Interlock LED changes from red to green) to enable the Ready indicator and begin lasing after

the five-second delay.

Over temperature fault

Over temperature faults occur when thermal limits in the laser are exceeded (the Temp LED changes from

green to red).
To reset an over-temperature fault on Keyswitch-equipped lasers, lower coolant temperature below °C

(f201), cycle DC power to the laser, and then cycle the Keyswitch from OFF/RESET to ON (or apply a ±5–

24 VDC Remote Reset/Start Request pulse with the Keyswitch set to ON). When the Ready indicator

illuminates, lasing is enabled after a five-second delay.

Important Note: Because of the over-temperature latch circuit, the Temp indicator remains red

prior to cycling power even after the laser has cooled sufficiently to begin operation. If the Temp

indicator remains red after cycling power, the laser is not sufficiently cooled—cool the laser for several

more minutes, cycle power, and then cycle the Keyswitch.

Over-temperature faults are now latched. To reset an over-temperature fault, lower coolant temperature

below 28 °C (f201) to cool the laser and then cycle DC power to the laser. Once the Temp indicator is

green and the Ready lamp is lit, lasing is possible after the five-second delay.

Under voltage fault

An under-voltage fault occurs when the DC input voltage falls below preset limits. This fault is indicated

by the Ready LED flashing 1 blink. To reset an under-voltage fault, first correct the voltage problem and

ensure that 96 VDC is measured at the laser under full-load conditions. Next, cycle DC power off and then

on again. On Keyswitch-equipped lasers, you must also toggle the Keyswitch from OFF/RESET to ON (or

apply a ±5–24 VDC Remote Reset/Start Request pulse with the Keyswitch set to ON). When the Ready

LED illuminates, lasing is enabled after a five-second delay.

Over voltage fault

An over voltage fault occurs when the DC input voltage rises above preset limits. This fault is indicated by

the Ready LED flashing 2 blinks. To reset an over voltage fault, first correct the voltage problem and ensure

that 96 VDC is measured at the laser under full-load conditions. Next, cycle DC power off and then on

again. On Keyswitch-equipped lasers, you must also toggle the Keyswitch from OFF/RESET to ON (or

apply a ±5–24 VDC Remote Reset/Start Request pulse with the Keyswitch set to ON). When the Ready

LED illuminates, lasing is enabled after a five-second delay.

Содержание f201










































































































Результаты поиска

Содержание f201

Отзывы:

Похожие инструкции для f201

Бренды по названию

Популярные бренды

Novanta f201, Руководство пользователя

Результаты поиска

Содержание f201

Отзывы:

Похожие инструкции для f201

Бренды по названию

Популярные бренды