Novanta f201 страница 90 Скачать руководство пользователя

Страница: 90 / 105

LASER FAULT INDICATIONS

PAGE

Laser fault indications

On f201 lasers manufactured after November 2007, Ready (RDY) and Shutter (SHT) LED’s flash to annun-

ciate one of four laser faults. The following table lists error codes, the corresponding fault, and describes

basic corrective action. See the following section, Resetting faults, for detailed corrective actions.

Table 5-9 Laser error codes.

Resetting faults

Remote interlock condition

A remote interlock condition occurs when the Remote Interlock input opens (the Remote Interlock LED

changes from green to red).
To reset a remote interlock condition on Keyswitch-equipped lasers, re-establish the Remote Interlock

signal input (Remote Interlock LED changes from red to green) and cycle the Keyswitch from OFF/RESET

to ON (or apply a ±5–24 VDC Remote Reset/Start Request pulse with the Keyswitch set to ON). When

the Ready indicator illuminates, lasing is enabled after a five-second delay.

Warning: Serious Personal Injury

On f201 OEM lasers, remote interlock faults are not latched. Clearing the fault condition re-enables

the Ready indicator and the laser will fire after the five-second delay provided that the Shutter

indicator is lit and a PWM Command signal is applied. Because exposure to 10.6

m CO2 laser

radiation can inflict severe corneal injuries and seriously burn human tissue, the OEM or System

Integrator must ensure that appropriate safeguards are in place to prevent unintended lasing.

Содержание f201










































































































Результаты поиска

Содержание f201

Отзывы:

Похожие инструкции для f201

Бренды по названию

Популярные бренды

Novanta f201, Руководство пользователя

Результаты поиска

Содержание f201

Отзывы:

Похожие инструкции для f201

Бренды по названию

Популярные бренды