Novanta f201 страница 87 Скачать руководство пользователя

Страница: 87 / 105

STATUS LEDS

PAGE

Status LEDs

f201 LED indicators, also mirrored as output signals on the User I/O connector, provide status information

to the user. Table below shows F201 laser output signal and LED indicator states during normal and fault

conditions. User I/O outputs are Closed when the state indicated by the signal name is True.

Table 5-2 Status signals.

When PWM Command pulses are applied (and are long enough to produce laser output) the Lase LED

illuminates red.
On OEM lasers, the Ready lamp illuminates on DC power-up when Remote Interlock and Temp indicators

illuminate green. After the Ready indicator illuminates, a five-second delay occurs before F201 laser is

permitted to lase.

Important Note: Note: f201 Ready and Shutter indicators (as well as Laser Ready and Shutter

Open outputs) denote separate control functions. Although the Ready lamp may light while the

Shutter LED is Off (Shutter Switch Closed or Shutter Open Request signal missing), no power is applied

to the RF boards until both Ready and Shutter indicators are illuminated.

Содержание f201










































































































Результаты поиска

Содержание f201

Отзывы:

Похожие инструкции для f201

Бренды по названию

Популярные бренды

Novanta f201, Руководство пользователя

Результаты поиска

Содержание f201

Отзывы:

Похожие инструкции для f201

Бренды по названию

Популярные бренды