Novanta f201 страница 23 Скачать руководство пользователя

Страница: 23 / 105

CONNECTING

PAGE

f201 cooling tubing connections

To connect cooling tubing to your f201 laser, refer to the figure below and perform the following steps.

The numbered items that follow correspond to the step numbers in the following procedure.

Figure 2-7 F201 cooling connections.

Cut and connect a length of cooling tubing to fit between the chiller’s Outlet port and the WATER

IN port on the rear of your f201 laser.

Cut and connect a length of cooling tubing to fit between the WATER OUT port on the rear of the

laser and the chiller’s Inlet port.

Turn on the chiller and adjust the temperature setpoint to 18 °C to 22 °C. Regulate coolant flow to

9.5 lpm (2.5 GPM) for f201 lasers at less than 414 kPa (60 PSI) of pressure.

Closely examine all cooling connections and verify that there are no leaks.

Locate the 1/2-inch O.D. cooling tubing in the Ship Kit and cut four lengths (12–18 inches long) to

fit partway between your chiller and the rear of the laser.

Select two lengths of tubing and connect one end of each piece to the laser’s WATER IN ports.

Connect the other end of each length of tubing to the “Y” fitting (included in the Ship Kit).

4 Cut and connect a length of tubing to fit between the chiller’s Outlet port and the center of the

“Y” fitting.

5 Select the other two lengths of previously cut 1/2-inch cooling tubing and connect one end of

each piece to the laser’s WATER OUT ports.

6 Connect the other end of each length of tubing to the other “Y” fitting.

7 Cut and connect a length of tubing to fit between the chiller Inlet and the center of the “Y” fitting.

8 Turn on the chiller and adjust the temperature setpoint to 18 °C to 22 °C. Regulate coolant flow

to 15.1 lpm (4.0 GPM) of pressure.

9 Closely examine all cooling connections, assure there are no leaks.

Содержание f201










































































































Результаты поиска

Содержание f201

Отзывы:

Похожие инструкции для f201

Бренды по названию

Популярные бренды

Novanta f201, Руководство пользователя

Результаты поиска

Содержание f201

Отзывы:

Похожие инструкции для f201

Бренды по названию

Популярные бренды