Notifier ID50 SERIES Скачать руководство пользователя страница 43

Страница: 43 / 94

ID50 Series Panel - Installation, Commissioning & Configuration Manual

Configuration

Mode

997-263, Issue 4

September 2002

5.4Level 3 Configuration Options

The Level 3 Configuration Options allow you to configure

the panel. These Options are listed in the menu map at

left. The default Level 3 passcode is given in

Appendix 1 -

Specifications

Before any configuration changes can be made, the memory

lock must be set to the unlocked position (see below).

Memory Lock Jumper Link

Jumper link MEM (J9) locks/unlocks the system

configuration. J9 is located to the left of the Digital / ÜE

terminal block (TB8). To configure the panel, J9 must be

in the unlocked position (link NOT fitted).

Fit the link to the jumper (J9) before returning to

normal operation.

Any attempt to access a configuration menu option while

the link is fitted will cause the following message to be

briefly displayed:

Memory is Locked!

MEM

LOCKED

UNLOCKED

Содержание ID50 SERIES































































































Результаты поиска

Содержание ID50 SERIES

Отзывы:

Похожие инструкции для ID50 SERIES

Бренды по названию

Популярные бренды

Notifier ID50 SERIES, Инструкция по установке, пусконаладке и конфигурации

Результаты поиска

Содержание ID50 SERIES

Отзывы:

Похожие инструкции для ID50 SERIES

Бренды по названию

Популярные бренды