A
B
C
+ -
C
B
A
+
-
A
B
C
+ -
3. SPECIFICATIONS
• Mount the speedo using the supplied thick/black doubled-sided tape.
• Position the speed-control where it is protected in the event of a crash.
• Install the speed-control so that you have easy access to the connector and buttons.
• Make sure there is enough clearance (about 3cm) between the speed-control, power-wires, antenna
and receiver. Avoid any direct contact between power components, the receiver or the antenna. This can
cause interference. If interference occurs, position the components at a different place in the model.
• The aerial should be run vertically up and away from the receiver. Avoid contact with any parts made of
carbon fibre or metal. If the aerial is too long, don’t coil up the excess length. It is better to cut it down
to a length of about 35 cm. See also the instructions supplied with your radio control system.
• Make sure there are enough cooling slits in the body. This will increase the performance and life of all the
electronic components.
4. INSTALLATION TIPS
2. CONNECTIONS
1. INSTALLATION
* Transistors rating at 25°C junction temperature Specifications subject to change without notice.
** measured at 7.2V
USER MANUAL
5. SUPPRESSION
BRU BRUSHED
over 3T (brushless - star)
over 4T (brushed)
# 90750
for distributor address see packaging
www.nosram.com
RA00183
BRUSHED MOTOR:
• Blue/Yellow power-wire
Speedo MOT.A/MOT.B to „Minus“ on the motor.
• Orange power-wire
Speedo MOT.C to „Plus“ on the motor.
BRUSHLESS MOTOR:
• Blue power-wire
Speedo MOT.A to motor „A“
• Yellow power-wire
Speedo MOT.B to motor „B“
• Orange power-wire
Speedo MOT.C to motor „C“
• Connect the hall sensor cable to the speed-control and the motor.
or
an
ge
or
an
ge
or
an
ge
blue
yellowyellow
blue
yellow
or
an
ge
Hall Sensor Wire
Together to minus
yellow
Receiver
wire
Hall Sensor
Connector
RECEIVER CONNECTING WIRE:
This NOSRAM speed-control is equipped with an NOSRAM Multicon receiver
wire. As supplied, it will easily fit in all ordinary receivers.
HALL SENSOR WIRE:
This bi-directional multipole wire (which comes with the motor and NOT the speed-control!) connects the
speed-control and the motor. Do not alter or modify this cable! There are replaceable/optional hall sensor
wires available: • #92510 (20cm)
• #92520 (10cm)
POWER WIRES:
For maximum performance, 12AWG power wires without any connectors are used. The unique splitted
solder-tabs allow easy and convenient replacement of the power wires. Nevertheless some soldering skills
are required. Avoid soldering longer then 5sec per soldering joint to prevent possible damage to the speed-
control due to overheating of the components! There is a full 12awg replacement power wire set available:
#92506
HEATSINK:
To achieve best perfomance even under extreme conditions, the heatsink has been directly
mounted to the speed-control. This ensures the best possible heat transfer away from the speed-control.
Caution:
Never attempt to remove the heatsink, because the speed-control will get damaged if you do this.
The heatsink is an integral part of the speed-control and therefore cannot be removed.
Because of the physical principles of brushless technology, the speed-controls do get a little hotter then
brushed systems. Therefore it is required to let the speed-control cool down completely after every run.
unt the power-capacitor in a position
where it is protected in the event of a crash.
he best place is right next to the speed-con-
trol (see picture). Secure it with doublesided
ONLY FOR BRUSHED MOTORS!
Motors with no capa-
citors or not enough capacitors may interfere with the
speed-control. To avoid this, solder the supplied capaci-
tors to your motor (see picture).
• Doublecheck all connections before connecting the speed-control to a battery.
CAUTION:
If battery is connected with reversed polarity it will destroy your speed-control!
• Red power-wire
Speedo BAT+ to battery „Plus“
• Black power-wire
Speedo BAT- to battery „Minus“
• The speed-control is now ready to be set-up (see section 6).
The NOSRAM MATRIX EVOLUTION ISTC is supplied with 12AWG power-wires without connectors. Be very
careful with the correct wire sequence/colors since an incorrect connection may damage the speed-cont-
rol! Avoid creating solder bridges on the solder-tabs and isolate all connections carefully.
Caution:
Avoid soldering longer then 5sec per soldering joint when replacing the power wires on the speed-
control and motor to prevent possible damage due to overheating of the components!
• Connect the speed-control to the receiver (position: Channel 2)
Dear Customer,
thank you for your trust in this NOSRAM product. By purchasing a NOSRAM MATRIX EVOLUTION ISTC
BrBrushed speed-control, you have chosen one of the most advanced speed-controls of today.
This speed-control with all of its high-tech features and specially selected electronic components is one of
the best speed-controls for Touringcars currently available on the market.
• Optimized XPS.2 software
• Special TC software
• Forward/Brake
• Low profile heatsink with integrated fan
• Automatic Brushless/Brushed adaption
• Smart-Temp-Readout-System
• Launch Control
• Redesigned brake
• 4, 5 and 6 cell optimized
• Large Power capacitor
Please read the following instructions to ensure, that your NOSRAM MATRIX EVOLUTION ISTC
BrBrushed speed-control always works up to your full satisfaction.
Please read and understand these instructions completely before you use this product!
With operating this product, you accept the NOSRAM warranty terms.
M
OT
.C (
Or
an
ge
)
M
OT
.B (
Ye
llo
w
)
Bru Brushed
yes
Voltage Input
4.8-7.4V
Bru Brushed Adaption
AUTOMATIC
Weight (excl. wires)
45.0g
Forward/Reverse
yes
B.E.C.
5.8V/3.0A
Case Size
33.1x37.6x32.5mm
High Frequency
yes
Typ. Voltage Drop (Brushless)* @20A
0.017V / phase
Sensored Brushless System
yes
Rated Current (Brushless)*
400A / phase
Multi-Protection-System
yes
Compatible winding styles (Brushless)
Star
Power Wires
12awg silicone flex
Rec. Motor Limit for Star winds (Brushless)**
for
for
over 3 turns
4, 5, 6 cell optimised
yes
Typ. Voltage Drop (Brushed)* @20A
0.012V
Smart-Temp-Readout-System
yes
Rec. Motor Limit (Brushed)**
over 4 turns
Launch Control
yes
Rated Current (Brushed)*
400A
Integrated he fan
yes
4 adjustable Modes (NiMH/LiPo, XPS.2/PMS.2 Power Profiles, Initial- and Automaticbrake)
yes
